Connecting To Your Computer Via Usb; Controlling Video (V-Link) - Roland Lucina AX-09 Manual De Usuario

Connecting to Your Computer
via USB
If you use a commercially available USB cable to connect
the Lucina AX-09's rear panel USB COMPUTER connector to
a USB connector of your computer, you'll be able to do the
following things using MIDI.
• Play your software synthesizers by performing the
Lucina AX-09.
• Record into your sequencer software by performing the
Lucina AX-09.
• Use your sequencer software to play the Lucina AX-09.
USB cable (sold separately)
* For.details.on.operating.requirements,.refer.to.the.
Roland.website .
Roland website
Here you can download the original driver, and view
installation instructions and operating requirements.
http://www.roland.com/
NOTE
• Only MIDI data can be transmitted or received via USB.
• Power-on the Lucina AX-09 before starting the MIDI
application on your computer. Do not turn the Lucina
AX-09's power on or off while your MIDI application is
running.
USB driver settings
Normally it will not be necessary to install a USB driver in
your computer. However if you experience problems with
the computer connection (if a malfunction occurs, or if
the performance is poor), you may be able to solve the
problem by downloading and installing Roland's original
driver as described below.
1. As.described.in. " USB.Driver.Settings".(p ..18),.change.
the.driver.setting.to."
2. Turn.the.Lucina.AX-09's.power.off,.and.then.on.
again .
3. Download.and.install.the.original.Roland.driver .
For details on downloading and installing the original
Roland driver, refer to the Roland website.
".(Vendor) .
un D

Controlling Video (V-LINK)

V-LINK ( ) is a function that allows music
and images to be performed together. By using MIDI to
connect two or more V-LINK compatible devices, you can
easily enjoy performing a wide range of visual effects
that are linked to the expressive elements of a music
performance.
For example, if you use the Lucina AX-09 in conjunction
with the EDIROL P-10, you'll be able to do the following.
• You can use the Lucina AX-09's keyboard to switch
images on the P-10.
• You can use the Lucina AX-09's touch controller to
control the speed of image playback.
This example shows the Lucina AX-09 connected to an
EDIROL P-10.
Use a MIDI cable to connect the Lucina AX-09's MIDI OUT
connector to the EDIROL P-10's MIDI IN connector.
EDIROL P-10
MIDI IN connector
* You.can't.perform.V-LINK.communication.via.USB .
Turning V-LINK On
1. Press.the.[V-LINK].button.to.make.it.light .
Operations on the Lucina AX-09
V-LINK data is transmitted on MIDI channel 15. The following
functions can be controlled from the Lucina AX-09.
Controller Explanation
Switch images.
* Normally, the keyboard will sound at the same
Keyboard
time that the clip is switched. If you don't want
(the.far-left.octave)
the keyboard to sound, change the Local Switch
setting to "OFF. "
Control the playback speed.
Touch.Controller
* However, the touch controller will also transmit
pitch bend data at the same time.
Local switch settings
1. Hold.down.the.[SHIFT].button.and.press.the.
[V-LINK].button.seven.times .
The display will indicate "
current setting will appear.
2. Continue.holding.down.the.[SHIFT].button,.and.
use.the.[INC/+]./.[DEC/–].(OCTAVE.[+]./.[–]).buttons.
to.change.the.setting .
Value Explanation
When V-LINK is on, the leftmost octave of the keyboard
o n
will sound.
When V-LINK is on, the leftmost octave of the keyboard
o FF
will not sound.
* This.setting.is.not.saved ..It.will.always.be.ON.when.the.
Lucina.AX-09.starts.up .
LC L
, " and then the value of the
21