Campbell Hausfeld DH7800 Instrucciones De Operación

See Warranty on page 8 for important information about commercial use of this product.
Operating Instructions
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.
Table of Contents
Description . . . . . . . . . . . . . . . . . . . . . 1
Unpacking . . . . . . . . . . . . . . . . . . . . . . 1
Safety Guidelines . . . . . . . . . . . . . . . . 1
Important Safety Information . . . . . . 1
Introduction . . . . . . . . . . . . . . . . . . . . 3
Spray Gun Setup . . . . . . . . . . . . . . . . . 3
Preparation . . . . . . . . . . . . . . . . . . . . . 4
Operation . . . . . . . . . . . . . . . . . . . . . . 5
User-Maintenance Instructions . . . . . 5
Troubleshooting Chart . . . . . . . . . . . . 6
Warranty . . . . . . . . . . . . . . . . . . . . . . . 8

Description

Air operated spray guns are designed
to perform a variety of painting,
coating, and finishing applications
using the power of compressed air .

Unpacking

After unpacking the unit, inspect
carefully for any damage that may
have occurred during transit . Make sure
to tighten fittings, bolts, etc ., before
putting unit into service .
Do not operate tool
if damaged during
shipping, handling or use. Damage
could result in bursting and cause injury
or property damage.

Safety Guidelines

This manual contains information
that is very important to know and
understand . This information is
provided for SAFETY and to PREVENT
EQUIPMENT PROBLEMS . To help
recognize this information, observe the
following symbols .
Danger indicates
an imminently
hazardous situation which, if not
avoided, WILL result in death or serious
injury.
© 2010 Campbell Hausfeld/Scott Fetzer
hazardous situation which, if not
avoided, COULD result in death or
serious injury.
hazardous situation which, if not
avoided, MAY result in minor or
moderate injury.
information, that if not followed, may
cause damage to equipment.
NOTE: Information that requires special
attention .
Important Safety Instructions
INSTRUCTIONS PERTAINING TO A
RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS
should always be followed, including
the following:
CALIFORNIA PROPOSITION 65
contain chemicals known to the State
of California to cause cancer and birth
defects or other reproductive harm.
Wash hands after handling.
dust when you cut, sand, drill
or grind materials such as
wood, paint, metal, concrete,
cement, or other masonry. This dust
often contains chemicals known to
cause cancer, birth defects, or other
reproductive harm. Wear protective
gear.
GENERAL
a . To reduce the risks of
electric shock, fire, and
injury to persons, read all
the instructions before
using the tool.
REMINDER: Keep your dated proof of purchase for warranty purposes!
Attach it to this manual or file it for safekeeping.
For parts, product & service information
visit www.chpower.com
Gravity Feed Spray Gun
Warning indicates
a potentially
Caution indicates
a potentially
Notice indicates
important
When using tools,
basic precautions
This product or
its power cord may
b . Be thoroughly familiar with the
You can
create
c . Only persons well acquainted with
labels and manual. Failure to follow
warnings, dangers, and cautions could
result in DEATH or SERIOUS INJURY.
d . Follow all local electrical and safety
Locate model and date code on
tool and record below:
Model No .: _____________________
Date Code: _____________________
Retain these numbers for
future reference .
controls and the proper use of the
equipment . Follow all instructions .
Contact your Campbell Hausfeld
representative if you have any
questions .
these rules of safe operation should
be allowed to use the unit .
Read and
understand tool
codes as well as the United States
National Electrical Codes (NEC) and
Occupational Safety and Health Act
(OSHA) .
IN270101AV 1/10