Cable Reference Guide; Emergency Stop Disengagement - Greenlee C3 Auto Whip Manual De Instrucciones

Operation (con't)

Cable Reference Guide

Use this reference guide when establishing your
machine's various settings. Note that your final settings
may vary considerably from the values listed. These
values are meant to be a starting point.
When trying to find the Notch Depth for a cable size,
use the Notch Depth parameter in the Reference Guide
as a starting point. Cut a whip at the value suggested
below and inspect the resulting notch. If the Notch
Blade made contact with the cable, but didn't cut deep
enough to break away, increase the Notch Depth. It
is recommended to increase the Notch Depth by .03.
Increasing the Notch Depth setting significantly more
than .03 between successive cuts runs the risk of
crashing the Notching Blade into the cable, which could
break the Notching Blade.
Cable
Clad
Cable Size
Material
12/2" Aluminum Solid with aluminum or insulated ground
12/2" Aluminum
Medical grade with bare aluminum ground
12/4" Aluminum
Solid with 16 AWG aluminum ground
12/4" Aluminum
Solid with 16 AWG aluminum ground (12AWG x 5 + 16AWG x 1)
Aluminum
10/4" Medical grade with 8AWG bare aluminum ground
Aluminum
6/3" Stranded with 8AWG ground
6/4" Aluminum Stranded with 8AWG stranded insulated ground
6/4" Aluminum Stranded, lightweight aluminum with ground
Aluminum
3/8" FMC, reduced wall
Aluminum
FMC, reduced wall extra exible
3/8"
Aluminum FMC, Flexible Aluminum
1/2"
Clad
Cable Size
Material
12/2" Steel Solid with ground; multi color-purple-black-white
12/2" Steel Medical grade; solid with green ground, bare aluminum
Steel Solid with insulated ground (12AWG x 3)
12/2"
Steel
12/3" Solid with 10 AWG bare aluminum ground
Steel Solid with 16/2 luminary solid, blue color
12/3"
Steel Solid with 16AWG aluminum ground; multi color
12/4"
Steel Solid with no assembly tape or paper
12/4"
Steel
Solid with no assembly tape or paper
10/4"
Steel
Solid
10/4"
Steel
Solid with steel jacket
10/4"
Steel Medical grade; solid with aluminum ground
10/4"
Steel
Stranded
6/4"
Steel
Stranded with 8AWG stranded insulated ground
6/4"
Steel FMC, extra- exible
1/2"
Steel FMC, extra- exible
1/2"
*Note: This table is only a guide. The parameters will vary from unit to unit and cable to cable. Be sure to inspect the rst piece of each run for any damage or issues and then adjust the settings accordingly.
Greenlee Tools, Inc.
Description
Description
C3 Auto Whip Clad Cable Cutter
Saw
Cable Dia. Notch Rate
Rate
0.44-0.49 25 50
0.510 25 50
0.540 25 50
0.57-0.58 25 50
0.656 20 30
15
0.813 30
0.950 15 30
15 30
0.980
0.575 7 8
0.505 7 8
0.910
7 8
Saw
Cable Dia. Notch Rate
Rate
0.467
15 30
0.490 15 30
0.510
20 30
30
0.500 15
0.580 30
15
0.550 15 30
0.535 15 20
20
0.635 15
15 20
0.645
0.650 15 20
15 20
0.660
0.950 10 20
10 20
0.950
0.825 7 8
0.890 7 8
25
4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
Control Adjustments
Notching Cutoff
Feed Rate
Tension Tension
500 1500 1600
500 3500 1600
500 3500 1600
500 3500 1600
500 3500 1600
5000
500 4500
5000
4500
500
4500 5000
500
2000 1600
500
2000
1600
500
4000 1600
500
Notching Cutoff
Feed Rate
Tension Tension
2000 1600
500
2000
500 1600
3000
1600
500
1600
500 3000
1600
2000
500
4500 1600
500
4200 1600
500
4200 5000
500
5000
500 4200
4200 5000
500
5000
500 4200
4500 5000
500
4500 5000
500
4000 1600
500
4200 1600
500
Notch Depth
0.970
0.970
0.940
0.900
0.800
0.760
0.630
0.57-0.59
1.000
1.000
0.690
Notch Depth
0.990
1.000
1.000
1.000
0.900
0.950
0.940
0.860
0.860
0.880
0.890
0.570
0.680
0.750
0.770