1. Manuales
  2. Marcas
  3. Metra Manuales
  4. Accesorios de Automóviles
  5. 99-3010S
  6. Instrucciones de instalación

Metra 99-3010S Instrucciones De Instalación

Ocultar thumbs Ver también para 99-3010S:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Descargar este manual
INSTALLATION INSTRUCTIONS FOR PART 99-3010S
Chevy Camaro 2010-up
KIT FEATURES
• DIN head unit provision with pocket
• ISO DIN head unit provision with pocket
• Double DIN head unit provision
• Stacked ISO DIN head unit provision
• Painted Silver to match factory finish
KIT COMPONENTS
• A) Radio trim panel • B) Radio housing • C) ISO brackets • D) ISO trim plate • E) Double DIN brackets
• F) DDIN trim plate • G) Pocket •H) Interface • I) 20-pin GM harness • J) 4-pin to 4-pin resistor pad harness
• K) 22-pin to 44-pin Camaro harness • L) 18-pin to 10-pin HVAC harness
A
B
C
H
I
METRA. The World's best kits.
APPLICATIONS
99-3010S
D
E
J
K
™
1-800-221-0932
F
G
L
metraonline.com
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness:
• Interface included
Antenna Adapter:
• 40-EU10 European antenna adaptor 2006-up
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• Socket wrench
CAUTION: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
NOTE: Refer to the instructions included with the
aftermarket radio.
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION

Publicidad

Capítulos

Tabla de contenido
loading

Manuales relacionados para Metra 99-3010S

Resumen de contenidos para Metra 99-3010S

  • Página 1 INSTALLATION INSTRUCTIONS FOR PART 99-3010S APPLICATIONS Chevy Camaro 2010-up WIRING & ANTENNA CONNECTIONS (sold separately) Wiring Harness: 99-3010S • Interface included Antenna Adapter: KIT FEATURES • 40-EU10 European antenna adaptor 2006-up • DIN head unit provision with pocket • ISO DIN head unit provision with pocket • Double DIN head unit provision • Stacked ISO DIN head unit provision • Painted Silver to match factory finish TOOLS REQUIRED • Panel removal tool • Phillips screwdriver • Socket wrench KIT COMPONENTS • A) Radio trim panel • B) Radio housing • C) ISO brackets • D) ISO trim plate • E) Double DIN brackets...

  • Página 2: Tabla De Contenido

    99-3010S Table of Contents Dash Disassembly Dash Disassembly 1. Unclip and remove the (2) side trim panels running the length of the – Chevy Camaro 2010-up ................... 2-3 center console. (Figure A) 2. Remove (1) 9/32” screw from Kit Preparation ......................3 each side of the front of the center console. (Figure B) Kit Assembly 3. Remove (2) 9/32” screws per side (Figure A) – DIN head unit provision with pocket ..............4 from the cover on the back of the center console then unclip and – ISO DIN head unit provision with pocket ...............4 remove the cover. (Figure C) – Double DIN/Stacked ISO DIN head unit provision .

  • Página 3: Dash Disassembly

    99-3010S Dash Disassembly Kit Preparation 4. Remove (2) 9/32” screws exposed 1. Cut and remove the sub dash under the cover on the back of radio support to make room for the console. (Figure D) interface and harnesses. (Figure A) 5. Lift up on the rear of the console 2. Remove panel clips from factory and slide toward the back of the radio and attach to the top of the vehicle then unclip and remove the kit housing. (Figure B) entire center console. (Figure E) Continue to kit assembly (Figure E) (Figure A) 6. Remove (2) 9/32” screws securing the climate control/radio trim panel and remove. (Figure F) 7. Remove (4) Phillips screws securing the radio chassis. (Figure G) Continue to kit preparation...

  • Página 4: Kit Assembly

    99-3010S Kit Assembly DIN head unit provision with pocket ISO DIN head unit provision with pocket 1. Slide the DIN cage into the radio 1. Mount the ISO brackets to the head housing and secure by bending unit with the screws supplied with the metal locking tabs down. the unit. (Figure A) (Figure A) 2. Snap the pocket into the bottom 2. Snap the pocket into the bottom opening of the radio housing. opening of the radio housing. (Figure B) (Figure A) (Figure A) (Figure B) 3. Slide the head unit into the radio 3. Slide the aftermarket head unit into opening until the side clips engage.

  • Página 5: Double Din/Stacked Iso Din Head Unit Provision

    99-3010S Kit Assembly Axxess Interface Installation Double DIN/Stacked ISO DIN head unit provision FEATURES 1. Cut and remove the center support • Provides accessory (12-volt 10-amp) (For DDIN only). (Figure A) • Retains R.A.P. (Retained Accessory Power) 2. Snap the Double DIN brackets to • Used in amplified or non-amplified systems the inside edge of the Double DIN • Retains all warning chimes radio housing. (Figure B) • Provides NAV outputs (parking brake, reverse, mute, and V.S.S.) (Figure A) • Retains OnStar/OE Bluetooth 3. Slide the Double DIN head unit or stacked ISO head units into the • Adjustable volume for chimes and OnStar bracket/radio housing assembly • High level speaker input...
  • Página 6 99-3010S From the 44-way harness: Axxess Interface front positive speaker output of the the left rear negative wire of the Installation aftermarket radio. aftermarket radio. • Connect the Black wire to the ground • Connect the Gray/Black wire to the From the 16-pin harness: wire of the aftermarket radio. For non-amplified vehicles: right front negative speaker output of • Connect the RCA’s to the AUX in on the • Connect the Red wires to the the aftermarket radio. • Cut the resistors from the Green, aftermarket radio (if equipped). ignition/accessory wire of the Green/black, Purple, Purple/Black • The Violet wire is not used in Note: This will allow you to retain the aftermarket radio.

  • Página 7: Installing Interface

    99-3010S Audio Level Adjustment Installing the aftermarket radio on. Push the OnStar Vehicle customization button, the radio should turn off (radio Interface with optional LCD 1) Start your vehicle and turn on the will mute if mute wire is connected) and radio having audio playing. (AXXESS part # XIA-LCD sold separately) 1. With all the connections completed, you should hear OnStar. Push the OnStar 2) Turn your aftermarket radio’s volume plug the 16 and 22-pin harnesses into cancel button and the radio should come The OEM radio is used to customize up ¾ of the way. the interface. back on. Cycle the A/C fan speed all the certain features of the vehicle.

  • Página 8: Changing Display Backlight Color

    INSTALLATION INSTRUCTIONS FOR PART 99-3010S Changing Display • Press and hid the “Face/Face” button to increase Green. Backlight Color • Press and hid the “Face/Def” button to 1. Press the front defrost button for 5 seconds, decrease Green. this will engage the “Configure Backlight • Press and hold the “Fan Up” button to Color” mode. Note, backlight will blink while increase Blue. in this mode. (Figure A) • Press and hold the “Fan Down” button to 2. Create your backlight color (Figure A): decrease Blue. • Press and hid the “Face” button to 3. After you have your desired color stop increase Red. pressing the button(s) and the blinking will • Press the “Foot” button to decrease Red. stop leaving your desired color. (Figure A) Green Blue NOWLEDGE IS...
  • Página 9 INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-3010S APLICACIONES Chevy Camaro 2010 y mas CABLEADO Y CONEXIONES DE ANTENA (se venden por separado) Arnés de cableado: 99-3010S • Se incluye interfase Adaptador de antena: CARACTERÍSTICAS DEL KIT • Adaptador de antena europea 40-EU10 •...

  • Página 10: Chevy Sonic 2012 Y Más Recientes

    99-3010S Indice Desmontaje del tablero Desmontaje del tablero 1. Desenganche y quite los (2) paneles de moldura laterales que – Chevy Sonic 2012 y más recientes ..............2-3 corren por la longitud de la consola central. (Figura A) Preparación del kit ....................3 2.

  • Página 11: Desmontaje Del Tablero

    99-3010S Desmontaje del tablero Preparación del kit 5. Levante la parte trasera de la 1. Corte y quite el soporte del radio consola y deslice hacia la parte del sub tablero para hacer espacio trasera del vehículo, luego para la interfase y los arneses.

  • Página 12: Ensamble Del Kit

    5. Vuelva a armar el tablero en orden (Figura B) (Figura B) radio 99-3010S en lugar del panel inverso al desensamble, usando el panel de moldura de radio 99- de fábrica. 3010S en lugar del panel de fábrica.

  • Página 13: Provisión De Unidad Central Doble Din/Iso Din Vertical

    5. Vuelva a armar el tablero en orden HERRAMIENTAS REquERIDAS inverso al desensamble, usando el • Cortador • Pelacables • Cinta • Conectores (p. ej., conectores a tope, panel de moldura de radio 99-3010S tapas acampanadas, etc.) en lugar del panel de fábrica. (Figura B)
  • Página 14 99-3010S Desde el arnés de 44 vías: Instalación de la la bocina positiva frontal derecha del cable negativo posterior izquierdo del interfase Axxess radio de mercado secundario. radio de mercado secundario. • Conecte el cable Negro con el cable • Conecte el cable Gris/Negro con la de conexión a tierra del radio de...

  • Página 15: Instalación De La Interfase

    99-3010S Instalación de la mercado secundario. Presione el botón radio mientras reproduce audio. Vehículo interfase personalización OnStar, el radio debe apagarse (el radio se 2) Aumente el volumen del radio de quedará en silencio si el cable de silencio está...

  • Página 16: Cambio De La Pantalla Color De Retroiluminación

    INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-3010S Cambio de la pantalla para aumentar Verde. color de retroiluminación • Pulse y escondió el “Face/Def” para disminuir Verde. 1. Pulse el botón de deshielo frontal durante 5 segundos, esto hará que el “Luz de fondo •...

Tabla de contenido