Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Fig. J
Mode Selector (Fig. A)
DCS356
Your tool is equipped with a mode selector
allows you to select one of the three modes. Select the
mode based on the application and control the speed of the
tool using the variable speed trigger switch
Lock On/Off Button (Fig. A)
Engage the lock on/off button
or right. When the trigger
1
button fully to either side until it snaps into place will lock
the trigger and disable it from being depressed. Placing
the button in the center position allows the trigger to
operate normally.
Pushing the button to the left or right with the trigger
depressed will lock the trigger in the depressed position.
This allows for more comfort and control in extended use
applications. Pressing the trigger switch again will release
the lock out and the tool will turn off upon release of
the trigger.
nOTE: The tool will automatically shut off after operating
for five minutes with the lock-on button engaged. To restart
the tool, the user will have to release the trigger and repress
lock-on button.
LED Worklight (Fig. A)

CAUTION: Do not stare into worklight. Serious eye
injury could result.
The LED worklight
2
will activate any time the trigger is
depressed and will remain on for 20 seconds after trigger
is released.
nOTE: The worklights are for lighting the immediate work
surface and are not intended to be used as a flashlight.
Variable Speed Trigger (Fig. A, J)

WARNING: Ensure switch is fully OFF before installing
the battery pack.
1. Install the battery pack.
2. To turn the tool ON, hold it as shown in Figure J and
press the variable speed trigger
nOTE: The further the trigger switch is depressed, the
faster the tool will operate. If in doubt about the proper
speed for your operation, test the performance at low
speed and gradually increase until a comfortable speed
is found.
11
which
10
1
.
4
by pushing it to the left
is not depressed, pushing the
1
.
3. To turn the tool OFF, release the variable speed
switch 
 1 
.
Sanding

WARNING: Fire hazard. When working on metal
surfaces, do not use a vacuum cleaner because
sparks are generated. Wear safety glasses and a
dust mask. Due to the danger of fire, do not use your
sander to sand magnesium surfaces. Do not use for
wet sanding.
nOTE: Do not rest fingers on platen during use. Move it in
long sweeping strokes across the surface, letting it do the
work. Light pressure is all that is required for sanding.

Helpful Hints

Always ensure the work piece is firmly held or clamped
to prevent movement. Any movement of the material
may affect the quality of the cutting or sanding finish.
Do not start sanding without having the sandpaper
attached to sanding platen.
Use coarse grit paper to sand rough surfaces,
medium grit for smooth surfaces and fine grit for the
finishing surfaces. If necessary, first make a test run on
scrap material.
Excessive force will reduce the working efficiency and
cause motor overload. Replacing the accessory regularly
will maintain optimum working efficiency.
Do not allow the sandpaper to wear away, it will
damage the sanding pad.
Always keep the blade sharp.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
English
11

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Dcs356

Tabla de contenido