Unpacking Instructions - Fanimation El Palisade FP240 Serie Manual Del Propietário

This Manual is Designed to Make it as Easy as Possible for You
to Assemble, Install, Operate, and Maintain Your Ceiling Fan
Tools Needed for Assembly
• One Phillips head screwdriver
• One stepladder
• One ¼˝ blade screwdriver
• One wire stripper
NOTE: Assemble with Hand tools Only!
▲WARNING
Before assembling your ceiling fan, refer to section on
proper method of wiring your fan (page 8). If you feel you
do not have enough wiring knowledge or experience,
have your fan installed by a licensed electrician.
For your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all
steps have been completed and will be helpful in fi nding your place should you be interrupted.
▲WARNING
Do not install or use fan if any part is damaged or
missing. This product is designed to use only those
parts supplied with this product and/or any accessories
designated specifically for use with this product by
Fanimation. Substitution of parts or accessories not
designated for use with this product by Fanimation could
result in personal injury or property damage. Contact
your retail store for missing or damaged parts.
1. Check to see that you have received the following
parts:
NOTE: If you are uncertain of part description, refer to
exploded view illustration. (Figure 1, page 15)
Ceiling
Canopy
Hanger Ball
Adapter
Assembly
Side B
Side A
Blade Holder
Packs (2 sets)
NOTE: The illustration shown is not to scale or its actual confi guration may vary, wires partially removed for clarity.
• Three wire connectors
(supplied)
7 9
• ⁄ ˝ ½˝ & ⁄ ˝ wrench
,
16 16
or socket wrench

Unpacking Instructions

Hanger Bracket
Assembly
Tube Assembly
Support Cable
Wiring outlet box and box connectors must be of type
required by local code. The minimum wire would be a 3-
conductor (2-wire with ground) of the following size:
Installed Wire Length
Up to 50 ft.
50 - 100 ft.
NOTE: Place the parts from the loose parts bags in a small
container to keep them from being lost. If any parts are missing,
contact your local retailer.
DAMP LOCATION CEILING FAN: If you have purchased a
Damp Location Ceiling Fan, you may only use light kits marked
suitable for use in damp locations.
•
Horizontal Tube Assembly
• Two Motor Assemblies
• Blade Holder pack containing:
– Four blade holders (red dot)
– Four blade holders (white dot)
– Eight blade arm covers
• Blade Cover Mount'g Hardware Bag
3
– Seventeen ⁄ ˝–24 x
16
– Fanimation screwdriver
• Blade to Hub Mount'g Hardware Bag
– Seventeen 10–32 x ½˝ screws
• Hanger Ball Adapter Assembly
• Ceiling Canopy
• Hanger Bracket Assembly
• 2-speed, C3 wall control
NOTE: An (24˝, 30˝, 36˝ or other available various lengths)
extension pole is required for installation. Extension poles must
be purchased separately.
Horizontal
Bag
Hardware Bag
3
Materials
Wire Size A.W.G.
14
12
• Support Cable bag:
– Ceiling Support Cable
– Cable Clamp
– 5˝ lag bolt
– 2˝ lag bolt
– 3 ⁄ ˝ flat washer
8
• Hardware bag:
– 2˝ lag bolt
3
⁄ ˝ screws – 5 mm allen wrench
8
– Four ¼˝–20 x ½˝ screws
– Two 5 ⁄ ˝–32 x 1˝ threaded rods
32
5
– Two ⁄ ˝–32 external lockwashers
32
– Two 5 ⁄ ˝ knurled knobs
32
– Six motor mounting screws
– Two ¼˝–20 x 2
– Two ¼˝–20 nylon lock nuts
– Four wire connectors
Motor Assembly (2)
C3 Wall Control
Blade Mounting
Hardware Bag
1 ⁄ ˝ cap head bolts
8
2-speed