Led Lenser X21R.2 Manual De Instrucciones página 6

LED LENSER® * X21R
be disposed of in the domestic trash.
In contrast to the Power Module (shaft with "Safety Ytrion Cell" battery
pack), a replacement of a "Safety Ytrion Cell" battery pack in a Power
Module may not be carried out. Neither is it permitted, after removal of
the "Safety Ytrion Cell" battery pack, to charge it in any other manner or
instead, to use different rechargeable or standard batteries in the Power
Module. The Power Module may only be opened once, for separation and
subsequent disposal of the Ytrion Cell battery pack and the shaft; any
other separation will render the manufacturer's warranty null and void.
In general, for the disposal of batteries as well as particularly for
Lithium batteries, accumulators and accumulator packs, the applicable
rule is that they may only be disposed of in a discharged state and in a
technically correct manner. If they are not discharged it has to be ensured
that short-circuits are not possible. This can be accomplished by sticking
non-conducting adhesive tape over the contacts before disposal. .
Basically, the possibility of short-circuits with rechargeable and alkaline
batteries must be eliminated, therefore they may neither be opened,
entered into the human body in any way, or be thrown into a fire.
15. Cleaning
For cleaning, please use a dry, clean and lint-free cloth.
If salt water is spilled on the lamp, it must be removed immediately.
If it is not possible to rotate the selection ring of the "Fast Action Switch"
smoothly any more, it must be separated from the X21R.2, and the
underside of both the ring and the lamp tube underneath the ring should
be cleaned of dirt. To do so unscrew and separate the lamp head from the
Power Module. Carefully remove the black O-ring of rubber that is located
above the lamp head thread. When the switch button is now pressed
deep, the selection ring can be removed over the switch button in the
direction of the thread. Please ensure that the small spring-loaded ball
including its casing above the switch button is not lost.
Both surfaces can now be cleaned and the parts can be assembled again
in the opposite sequence.
If the reflector lens has gotten loose in the lamp head or, e.g. dirt has
been deposited on its inner side, you can apply the following remedial
measures.
The front ring of the X21 lens head, indicated by the 12 dents along the
periphery, can be unscrewed. There is a plastic ring inside that fixes
the reflector lens which can be tightened or removed for cleaning. You
can clean the reflector lens, if required, with a dry, lint-free clean cloth.
Afterwards, please assemble everything in the opposite sequence.
16. Scope of delivery
The X21R.2 is supplied in a hard case with the following accessories:
Pro
1 Floating Charge System
1 main plug
1 charger with extension cable (Input: 100 V to 240 V / 50 Hz to 60 Hz)
1 magnetic charging socket (magnetic charger) with cable and blue
position light as connection between the charger and the X21R.2
1 charger bracket – for fastening the charger components, e.g. to a wall
1 x operating manual
1 x front cap rubber cover
1 x end cap rubber cover
1 x carry belt
1 x rechargeable battery
Additional accessories for the X21R.2 are available (colour filter etc.).
You can get information on these additional accessories on our website
www.ledlenser.com.
17. Caution:
Do not swallow any small parts or batteries that are present. The product
or parts thereof (including batteries) must be stored outside the reach of
children.
For reasons of safety and approval (CE), the product must not be modified
and/or changed. The product is to be used exclusively as a pocket
torch. If the X21R.2 is used for any other purpose or used incorrectly,
it can get damaged and a hazard-free use can no longer be guaranteed
(danger from fire, short-circuit, electric shock etc.). There is no liability
for harm to individuals or damage to property and the warranty of the
manufacturer will be rendered null and void when the product is used in
an unintended manner.
The X21R.2 can be operated between the temperatures of -20 C° and
+50 C° (or -4 F° and 122 F°). Ensure that the X21R.2 is not subjected
to extreme temperatures, intense vibrations, explosive atmosphere,
solvents and/or vapours. Also continuous exposure to direct sunlight,
high humidity and/or moisture must be avoided.
Changes, repairs and maintenance other than those described in the
documents accompanying the product may only be carried out by
authorised technical personnel.
If it is found that the product –despite having been properly charged and
correctly assembled- cannot be operated in a safe and normal manner,
or the product shows damage, it must be rendered inoperative and must
not be used any further. In this case, contact your dealer for warranty
and/or repair.
05
.2
18. Safety instructions
This product is not a children's toy.
Since it has small parts that can be swallowed, it is especially not
suitable for those under the age of 5.
The article must not be used for examinations of the eyes (e.g. for the so-
called pupil test).
During the use of the product, proper heat dissipation should be ensured,
e.g. coverage of the lamp is to be avoided.
If the product does not work correctly, the user should first ensure that
the battery is charged and the lamp is properly assembled, i.e. the shaft
and the lamp head are screwed tightly together.
If using in traffic, please follow the respective legal regulations.
Because of t the permanent magnets in the selection ring of the "Fast
Action Switch" and in the magnetic charging socket of the Floating Charge
PRO
System , both the parts must always be a safe distance away from
items such as heart pacemakers or other magnetic storage medias.
The main hazard of this product is from the optical radiation in the blue-
light range (400 nm to 500 nm). Thermal hazard threshold values have
not been clearly determined.
The risk for the viewer depends on the use or on how the product is
installed. However, there is no optical hazard as long as the aversion
responses limit the time of exposure and as long as the information
contained in this instruction manual is read.
The aversion reactions triggered by the exposure are natural reactions
that protect the eye from the hazards of optical radiation. This includes in
particular conscious aversion reactions such as eye or head movement
(e.g. turning away).
When using the product it is of particular importance to bear in mind that
the aversion reactions of persons at whom the light is directed at may be
weakened or completely suspended as a result of medication, drugs or
illness.
Because of the blinding effect of the product, improper use may lead to
reversible, i.e. temporary impairment of sight (physiological blinding)
or afterimages, or it may trigger feelings of queasiness and tiredness
(physiological blinding). The intensity of the temporary feeling of being
unwell or the time until it subsides depend primarily on the difference in
brightness between the blinding-light source and the surrounding area.
Photosensitive people in particular should consult a medical consultant
prior to using this product.
Generally speaking, high-intensity light sources carry a high secondary
hazard potential due to their blinding effect. Just like looking into
other bright light sources (e.g. headlights of a car), the temporary
limited impairment of vision and afterimages may lead to irritation,
inconveniences, impairments and even accidents, depending on the
situation.
This information provided applies only to the use of this single product. If
more light-emitting products of the same type or of a different type are
used together, the intensity of the optical radiation may increase.
Any prolonged eye exposure with the source of radiation of this product
and the use of additional beam-focussing devices, must be avoided! When
exposure to the light beam occurs, eyes should be deliberately closed and
the head should be turned to avoid further exposure.
In case of a commercial use or the product's use by public bodies, the
user must be instructed as to all applicable laws and regulations that
correspond to the individual case of usage.
Important rules of conduct:
Do not aim the light beam directly into the eyes of a person.
The user or any other person should not look directly into the light beam.
In the event of optical radiation hitting the eye, one must shut their eyes
and turn their head away from the beam.
The instruction manual and this information must be stored safely and
must be passed on together with the product.
It is prohibited to look straight into the light that is being emitted by this
product.