Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
E N G L I S H
Using an extension cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data). The minimum conductor
2
size is 1.5 mm
. When using a cable reel, always
unwind the cable completely. Also refer to the table
below.
Conductor size (mm
2
)
0.75
1.00
1.50
2.50
4.00
Voltage
Amperes
115
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
230
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Fitting and removing 1/4" hex. drive accessories
(fig. B)
Your D
WALT Screwdriver has a 1/4" hexagonal
E
drive system. The drive accessory is retained in the
holder by a ball and a spring which engages in a
groove in the accessory shank.
• Remove the collar (4) by pulling it forward.
• To insert the accessory (e.g. a bit holder or
nutsetter) (7) push it into the holder (8) until it
snaps in place. Tap it lightly if required.
• To remove the accessory pull it out of the holder
using a pair of pliers.
en - 4
Cable rating (Amperes)
6
10
15
20
25
Cable length (m)
7.5
15
25
30
45
Cable rating (Amperes)
6
6
6
6
6
6
6
6
15
6
6
10
15
20
10
10
15
20
20
15
15
20
25
25
20
20
25
-
6
6
6
6
6
6
6
6
6
6
6
6
10
10
10
10
10
15
15
15
15
15
20
20
20
20
20
25
• Reinstall the collar (4) by aligning the ribs (9)
on the inside of the collar (4) with the grooves (10)
in the clutch housing and snap the collar in place.
Replacing the bit tip (fig. B)
• Simply pull out the bit tip (11). A pair of pliers may
be required.
Setting the driving depth (fig. C)
The depth sensitive feature offers the following
advantages:
- the selected driving depth is repeatable for
structural integrity
- screws with sealing washers are driven correctly
so that no leaks occur
The driving depth is determined by the position of
60
the depth locator (5) in relation to the bit or socket.
The symbols on the collar indicate how to set the
6
10
driving depth.
15
• Turn the collar clockwise to increase the driving
20
depth.
25
• Turn the collar counterclockwise to decrease the
-
driving depth.
-
-
6
6
Setting the direction of rotation (fig. D)
6
6
• Select forward or reverse rotation using the
15
forward/reverse switch (3) (see arrows on tool).
15
20
-
Instructions for use
Screwdriving or nutsetting (fig. A)
• Select the appropriate bit for the screw (or nut)
to be driven.
• Select forward or reverse rotation as described
above.
• To run the tool, press the variable speed switch (1).
The pressure exerted on the variable speed switch
determines the tool speed.
• If necessary, press the lock-on button (2)
for continuous operation and release the variable
speed switch. The lock-on button works only in
full speed, forward and reverse rotation.
Always wait until the motor has come to
a complete standstill before changing the
direction of rotation.
Always observe the safety instructions
and applicable regulations.
15
Publicidad
Capítulos
Tabla de contenido
