Fender Bassman 200 Instrucciones De Funcionamiento página 7

B B
B B
540W
A
Lift
Gnd
B
SERIAL NUMBER
Ground
Lift
TYPE: PR 419
A. IEC LINE CORD CONNECTOR - The power line cord must
be connected to a grounded AC receptacle in accordance
with the voltage and frequency ratings as labeled on the
Rear Panel under INPUT POWER.
B. GROUND LIFT - Switch IN disconnects the ground circuit
from the LINE OUT jack {C} (pin-1) which may reduce
noise or hum. Switch OUT is usually the best setting.
C. LINE OUT - Balanced XLR jack for output to recording or
sound-reinforcement equipment.
D. LINE OUT LEVEL - Adjusts the output level of LINE OUTjack {C}.
E. PRE/POST EQUALIZATION - Switch IN supplies the LINE
OUT jack {C} with the post-equalization (EQ modified) signal
from the amplifier. Switch OUT supplies the LINE OUT jack
{C} with the pre-equalization (EQ unmodified) signal.
F. TUNER - Connect your instrument tuner at this output jack.
This is the only output NOT disabled by the MUTE switch
allowing for quick, silent tuning of your bass while plugged
into the Bassman 200.
TYPE
PART NUMBERS
POWER REQUIREMENTS
POWER AMPLIFIER
PRE AMPLIFIER
SENSITIVITY FOR FULL POWER:
TONE CONTROLS
SEMI-PARAMETRIC CONTROL:
EFFECTS LOOP
SPEAKERS
DIMENSIONS
WEIGHT
a a s s s s m m a a n n
a a s s s s m m a a n n 2 2
2 2
MADE IN MEXICO
Line Out
Line
Level
Out
Tuner
D
C
Post
F
Pre
E
Pre/Post
EQ
S S p p e e c c i i f f i i c c a a t t i i o o n n s s
S S p p e e c c i i f f i i c c a a t t i i o o n n s s
PR 419
022-4504-000 (120V, 60Hz) USA,
022-4544-000 ( 230V, 60Hz) UK,
022-4574-000 (100V, 50/60Hz) Japan
540W
OUTPUT: 200W RMS into 4Ω @ <1%THD
SENSITIVITY: 1V RMS
INPUT IMPEDANCE: PASSIVE: 1MΩ,
PASSIVE: 20mV,
NOMINAL LEVEL: PASSIVE: 150mV,
BASS: ±15dB @ 50Hz
MID FREQUENCY: 150 to 1500Hz
MID LEVEL: ±15dB @ MID FREQUENCY setting
TREBLE: ±15dB @ 5kHz
ROOM BALANCE: ± 10dB, crossover frequency: 350Hz
SEND IMPEDANCE: 1kΩ
RETURN IMPEDANCE: 22kΩ
NOMINAL LEVEL: +4dBu
LOW FREQUENCY: Fender Special Design 4Ω, 15" Woofer (P/N 0048941000)
HIGH FREQUENCY: Foster Compression Driver (P/N 0048847000)
HEIGHT:
WIDTH:
DEPTH:
Product specifications are subject to change without notice.
0 0 0 0 - R R e e a a r r P P a a n n e e l l
0 0 0 0 R R e e a a r r P P a a n n e e l l
G. EFFECTS RETURN - Connect the cable from
the output of your external effects device to
this input jack.
Return Send
H. EFFECTS SEND - Connect cable from this
G H
output jack to the input of your external effects
device.
• LINKING
AMPLIFIERS: For additional output, link two Bassman
200's together by connecting the EFFECTS SEND jack {H}
from the "primary" amp to the EFFECTS RETURN jack {G}
of the "secondary" amp. All settings on the primary amp will
control the secondary amp settings except MASTER
VOLUME which must be set on each Bassman 200 .
I. HORN LEVEL - Adjusts the
volume level of the horn.
The horn is OFF with the
knob turned
clockwise to "Min."
J. FUSE - Protects the horn
from overdrive or electrical
fault damage. Replace fuse with same type and rating
(2A, 250V).
25.5 in. (65 cm)
23 in. (59 cm)
13 in. (33 cm)
65 lb. (30 kg)
7
TWO BASSMAN
counter-
022-4534-000 (240V, 50Hz) Aust,
022-4564-000 (230V,50Hz) Eur,
ACTIVE: 1MΩ
ACTIVE: 40mV
ACTIVE: 300mV
200