La-Z-Boy PowerRecline Instrucciones De Operación página 12

Ocultar thumbs Ver también para PowerRecline:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

La-Z-Time
PowerRecline
®
Assembly Instructions
Motion-Modular units with metal base rails have one bracket in the back and one "U" bracket in the
front on the right side (sitting) of modular units without right side arms, and two stud mounts with
threaded studs on the left side (sitting) of modular units without left side arms (F
Motion-Modular units with wood legs have one side mount bracket in the back and one "U" bracket
in the front on the right side (sitting) of modular units without right side arms, and two threaded
studs on the left side (sitting) of modular units without left side arms (F
17. Use a T-30 torx driver to loosen the threaded studs to approximately 1"; this measurement may
vary depending on the fabric and style (F
side (sitting) of modular units without left side arms.
18. To start, place the units to be attached next to each other, about 2" apart. Position the unit with the
threaded studs slightly behind the unit with the attachment brackets. Separate the fronts of the
units to be connected, about 6" apart. Slide the rear of the unit with the threaded studs toward the
unit with the attachment brackets, aligning the threaded studs to the rear bracket. Pull the unit with
the threaded studs forward to engage the rear bracket.
WARNING
– To reduce the risk of serious injury:
• The front of the unit must be raised to engage the front bracket. Please seek assistance
if you are unable to lift at least 57 pounds.
• Keep feet clear of the unit when lowering into position.
NOTICE:
To reduce the risk of product damage –
• Lift from the base rail. Do not lift from the upholstery or the bottom of the legrest.
19. Lift the front of the unit with the threaded stud approximately 3" off the ground, aligning it
to the unit with the attachment bracket. Gently lower the threaded stud into the front attachment
bracket (F
20). Keep feet clear of the unit when lowering into position.
IGURE
Note: Due to variations in upholstery and style, the threaded stud length may need to be adjusted to
fit into the attachment brackets or control gaps between units. Loosen or tighten the threaded studs
to provide adequate clearance.
20. Continue connecting the modular units until all have been securely joined.
21. Proceed to the Battery Backup Assembly Instructions to complete assembly.
NOTICE:
To reduce the risk of product damage –
• Do not move the units while connected together. The purpose of the bracket system is
to connect the units and prevent them from being separated while on the floor. The bracket
system does not provide adequate structural support for the movement of connected units.
22. All modular units must be disconnected to safely move the modular group. To disconnect the
units, lift up the left side (sitting) modular unit (with threaded studs) approximately 3" to clear
the front attachment bracket, move the front of the unit over and return it to the floor. Slide the
unit with the threaded studs backward to disengage the rear bracket.
22
Motion-Modulars
+
17).
IGURE
18).
IGURE
19). The threaded studs are located on the left
IGURE
La-Z-Time
PowerRecline
®
Assembly Instructions
F
17
IGURE
Rear Rail Bracket
Front Rail
"U" Bracket
F
18
IGURE
Rear
Side
Mount
Bracket
Front Side Mount
"U" Bracket
F
19
IGURE
Threaded
Threaded
Stud
Stud
"
"
1
1
Stud
Mount
Base Units
Leg Units
Motion-Modulars
+
Threaded
Stud
Stud
Mount
Threaded
Stud
F
20
IGURE
Front Rail "U"
Front Side Mount
Bracket
"U" Bracket
Base Units
Leg Units
23

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Powerrecline+

Tabla de contenido