Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
GB
of beeps for several seconds. The timer
indicator will display a flashing 00 besi-
de the indicator of the hotplate that has
been disconnected.
If you wish to time another hotplate at
the same time, repeat steps 3 and 4.
If the heating zone turned off is hot, its
indicator shows an H or otherwise an 0.
To turn off the audible signal touch any
sensor.
Changing the programmed time.
To change the programmed time, you
must press the touch key of the timed
hotplate (4) to select it and then the
clock
(6). You may then read and
change the time.
DISCONNECTION OF THE TIMER
If you want to stop the timer before the
programmed time is up.
1 First select the hotplate and then
press clock touch key
2 Use the touch key
ce the time to 00. The clock is can-
celled.
For quick switch-off: repeat step 1 as
above. Simultaneously pressing the
and
touch keys (12 and 11) the
timer will be disconnected.
Fondue function
(depending on model)
This function is specially intended for
melting butter, cheese, chocolate, etc.
It uses a power level that is lower than
level 1. To access the function:
1 Activate the desired hotplate to
power level 1.
2 Press touch key
indicator will switch to displaying
the
symbol.
To deactivate the function it is sufficient
to press the touch keys
(12/11), and the indicator will switch to
respectively displaying the lower
power level 0 or the higher one 1.
Synchro function
(depending on model)
Using this function, it is possible that
two hotplates, identified in the screen
printing, work jointly, both to select a
power level as well as to activate the
20
timer function.
To activate this function simultane-
ously press the two related selection
touch keys (4). On doing this, the two
decimal points (9) of the hotplates will
light up and they will both be set to
power level 0.
To deactivate this function, again
simultaneously press the two related
selection touch keys (4).
Power Management func-
tion (depending on model)
Some models are equipped with a
power limiting function. This function
allows the total power generated by
the hob to be set to different values
selected by the user. To do this, for the
first minute after having connected the
hob to the power supply, it is possible
to access the power limiting menu.
1 Press the "+" touch key for three
seconds. The letter PL will appear
(6).
on the clock
has a timer or on the hotplate indi-
(11) to redu-
cators (if it is not equipped with
one).
2 Press the locking touch key
The different power values to which
the hob can be limited will appear
and these can be changed using
the "+" and "-" touch keys.
3 Once the value has been selected,
once again press the locking touch
key
to the chosen power value.
If you want to change the value again,
you must unplug the hob and plug it in
again after a few seconds. Thus you
will again be able to enter the power
limiting menu.
Every time the power level of a hotpla-
(11). The
te is changed, the power limiter will
calculate the total power the hob is
generating. If you have reached the
total power limit, the touch control will
not allow you to increase the power
or
level of that hotplate. The hob will beep
and the power indicator (3) will blink at
the level that cannot be exceeded. If
you wish to exceed that value, you
must lower the power of the other hot-
plates. Sometimes it will not be
enough to lower another by a single
level as this depends on the power of
each hotplate and the level it is set at.
It is possible that to raise the level of a
large hotplate that of several smaller
ones must be turned down.
(6), if the model
(8).
(8). The hob will be limited
If you use the quick switch-on at maxi-
mum power function and the said
value is above the value set by the
limit, the hotplate will be set to the
maximum possible level. The hob will
beep and the said power value will
blink twice on the indicator (3).
Safety switch off function
If due to an error one or several hea-
ting zones do not switch off, the
appliance will be automatically discon-
nected after a set amount of time (see
table 1).
Table 1
MAXIMUM
Selected
OPERATING TIME
power level
(in hours)
Models with
Fondue function
8
1
8
2
5
3
4
4
4
5
3
6
3
7
2
8
2
9
1
P
10 or 5 mins.*
* Depends on model
When the "safety switch off" function
has been triggered, a 0 is displayed if
the glass surface temperature is not
dangerous for the user or an H if there
is a burn risk.
Keep the control panel of the
heating areas clean and dry at all
times.
In the event of operating pro-
blems or incidents not mentioned in
this
manual,
disconnect
appliance and contact the TEKA
technical service.
Suggestions and
recommendations
* Use pots or pans with thick, comple-
tely flat bottoms.
* Pots/pans with a smaller diameter
than the shown heating area are not
recommended.
* Do not slide pots and pans over the
glass because they could scratch it.
Models without
Fondue function
-
8
8
5
4
4
3
2
2
1
10 or 5 mins.*
the
Publicidad
Tabla de contenido
