Product Description; Safety Instructions - PLYMOVENT MOBILEGOplus Manual De Instalación Y De Uso

1.5 ambient and process conditions
Process temperature:
- min.
- nom.
- max.
Max. relative humidity
Suitable for outdoor use
1.6 Transport of the unit
You cannot hold the manufacturer liable for any transportation
damage after delivery of the product.
- Handle the filter unit and the accompanying extraction arm
with care.
- Completely dismount the extraction arm before transport.
Dismount the arm by executing the mounting procedure in
reverse order. Subsequently the filter unit and the arm can
be transported on a pallet in the original packing.
- To prevent damage, make sure that the filter unit and the
arm cannot shift on the pallet.
2

pRoducT dEScRipTioN

2.1 components
The product consists of the following main components and
elements:
Fig. 2.1
A shut-off damper
B extraction arm
C control panel
D pre filter cassette
E HEPA filter cassette
F fan + motor
A
Fig. 2.1 Main components and elements
2.2 operation
The MobileGo works in accordance with the recirculation
plus
principle. Welding fume is extracted through the hood of the
connected extraction arm by the built-in fan. The polluted air
0000115336/010518/0 MobileGo
5°C (41°F)
20°C (68°F)
70°C (158°F)
90%
no
B
C
D
E
F
60Hz
plus
passes the pre filter cassette and is cleaned by the HEPA filter
cassette.
The cleaned air is returned in the workshop through the outlet
grid on the rear of the unit.
2.2.1 Indication of filter replacement
The MobileGo has a service indicator that monitors the
plus
airflow. When the red indicator light (LED) is on, it is
necessary to replace the filter(s).
3

SaFETy iNSTRucTioNS

general
The manufacturer does not accept any liability for damage to
the product or personal injury caused by ignoring of the safety
instructions in this manual, or by negligence during
installation, use, maintenance, and repair of the product
mentioned on the cover of this document and any
corresponding accessories.
Specific working conditions or used accessories may require
additional safety instructions. Immediately contact your
supplier if you detect a potential danger when using the
product.
The user of the product is always fully responsible for
observing the local safety instructions and regulations.
observe all applicable safety instructions and
regulations.
user manual
- Everyone working on or with the product, must be familiar
with the contents of this manual and must strictly observe
the instructions therein. The management should instruct the
personnel in accordance with the manual and observe all
instructions and directions given.
- Do not change the order of the steps to perform.
- Keep the manual with the product.
users
- The use of this product is exclusively reserved to authorised,
trained and qualified users. Temporary personnel and
personnel in training can only use the product under
supervision and responsibility of skilled engineers.
- Stay alert and keep your attention to your work. Do not use
the product when you are under the influence of drugs,
alcohol or medicine.
- The product is not to be used by children or persons with
reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given
supervision or instruction.
- Children must be supervised not to play with the product.
intended use
3
The product has been designed exclusively for extracting and
filtering gases and particles which are released during the
most common welding processes. Using the product for other
purposes is considered contrary to its intended use. The
manufacturer accepts no liability for any damage or injury
resulting from such use. The product has been built in
accordance with state-of-the-art standards and recognised
safety regulations. Only use this product when in technically
perfect condition in accordance with its intended use and the
instructions explained in the user manual.
Technical specifications
Do not change the specifications given in this manual.
3. "Intended use" as explained in EN-ISO 12100-1 is the use for which the
technical product is suited as specified by the manufacturer, inclusive of his
directions in the sales brochure. In case of doubt it is the use which can be
deduced from the construction, the model and the function of the technical
product which is considered normal use. Operating the machine within the
limits of its intended use also involves observing the instructions in the user
manual.
EN - 4