Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

65R-C & 65R-TC Manual Pipe Threader Instructions
RIDGID
®
65R-C and 65R-TC Threaders are designed to
thread 1" to 2" pipe and conduit using a manually operated
internal ratchet.
Read these instructions carefully before
WARNING
using this tool. Failure to follow all instructions may
result in property damage and/or serious injury.
Thread Size Adjustment
1. Place threader with workholder up (Figures 1 and 2)
and unscrew workholder by turning counter-clockwise
until change plate is clear of posts.
2. Move post to desired pipe size. Screw workholder
clock wise until change plate slides over post.
3. Adjust change plate to desired thread size.
Standard Size Thread: Set change plate between the two
"Standard" marks.
Oversize Thread: For oversize (shallow) thread, set change
plate slightly below the "Standard" marks.
Undersize Thread: For undersize (deep) thread, set change
plate slightly above the "Standard" marks.
Gauge
Ring
Post
Release Cam
Lever
Figure 1 – 65R-C Threader
Gauge
Ring
Lugs
Workholder
Post
Change
Plate
Figure 2 – 65R-TC Threader
Printed in U.S.A.
EC40741
Threading
1. Inspect the threader before use. Replace dies or any
other part that shows damage or wear. To insure high
thread quality, only use RIDGID replacement dies.
WARNING
and high handle forces.
2. Mount the pipe firmly in a pipe vise. When threading an
existing pipe, make sure it is secure and will not move.
Cut the end of the pipe cleanly and squarely using a
pipe cutter (Figure 3) .
WARNING
should also be supported with a pipe stand. Vise and
stands should be on level ground.
WARNING
ator should be properly secured to prevent injury in the
event of a fall.
Workholder
Jaw
Clamp
Screw
Standard
Figure 3 – Cutting End Of Pipe
Marks
3. Ream the end of the pipe to remove any burrs that may
have been produced during the cutting of the pipe
(Figure 4) .
Change
Plate
Locking
Cam
Workholder
Jaw
Figure 4 – Reaming End Of Pipe
4. Adjust thread size for the size pipe to be threaded (refer
to previous instructions for thread size adjustment).
5. Adjust workholder:
65R-C: Turn gauge ring until desired pipe size corresponds
with mark on top of workholder (Figure 1) .
65R-TC: Turn gauge ring until desired pipe size is aligned
with locking cam (Figure 2) .
RIDGID
®
5/14
Worn dies can result in poor thread quality
To prevent tipping, long lengths of pipe
When working on a scaffold or lift, the oper-
999-998-280.10
REV. C

Publicidad

Tabla de contenido
loading

Resumen de contenidos para RIDGID 65R-C

  • Página 1 Post 5. Adjust workholder: Change 65R-C: Turn gauge ring until desired pipe size corresponds Plate with mark on top of workholder (Figure 1) . 65R-TC: Turn gauge ring until desired pipe size is aligned Figure 2 –...
  • Página 2: Changing Dies

    65R-C & 65R-TC Manual Pipe Threader Instructions 6. Turn release cam lever to the “closed” position. Slide 10. Apply a generous quantity of RIDGID Thread Cutting threader on the pipe with the workholder end first (Fi - Oil when threading (Figure 6) . Use of a lubricating oil gure 5) .
  • Página 3: Réglage Du Pas De Filetage

    65R-C & 65R-TC Manual Pipe Threader Instructions For name and address of your nearest Independent Author - Came de ized Service Center, contact the Ridge Tool Company at blocage Bague de (800) 519-3456 or http://www.RIDGID.com calibrage Fileteuse manuelle 65R-C et 65R-TC : Goujons Mode d’emploi...
  • Página 4 (environ un tour) avant de lancer le système d’entraînement. 5. Réglez l’anneau de serrage : 65R-C : Tournez la bague de calibrage jusqu’à ce que le repère de section approprié s’aligne sur le repère en tête de l’anneau de serrage (Figure 1) .
  • Página 5: Remplacement Des Filières

    «STANDARD. Instrucciones de uso NOTA ! Eliminez toutes traces d’huile laissée au sol. En Las Roscadoras Manuales 65R-C y 65R-TC de RIDGID ® fin de chantier, nettoyez systématiquement la file- han sido fabricadas para roscar tubos y conductos de una...
  • Página 6 Para labrar roscas de alta calidad, sólo 65R-C: Gire el calibrador anular hasta que el tamaño del emplee terrajas de recambio RIDGID. tubo concuerde con la marca encima del portapiezas (Figure 1) .
  • Página 7: Cambio De Terrajas

    10. Aplique abundante cantidad de Aceite para Cortar esta máquina, sólo deben usarse repuestos idénticos. Se Roscas de RIDGID cuando rosque (Figura 6) . No crea el riesgo de que ocurran lesiones graves si no se emplee un aceite lubricante o un aceite de roscar de respetan estas instrucciones.
  • Página 8 Nos. 65R-C & 65R-TC Pipe & Conduit Threaders Nos. 65R-C & 65R-TC Capacity: 1", 1 ", 1 " and 2" 31 18 Note: No. 65R-C Workholder Assembly (C-81-X) can be used for replace- ment on No. 65R-P Threader Die Set (High Speed, Special...

Este manual también es adecuado para:

65r-tc

Tabla de contenido