Publicidad
Idiomas disponibles
Idiomas disponibles
Use:
- Unroll the cable completely before plugging it in.
- Connect the appliance to the mains.
- To avoid a fierce start up of the fan, it is advisable to
start off from the lowest speed position and, once the fan
has been switched on, progressively increase the speed
to the desired position.
Fan function:
- Insert the power cord into plug socket and hear a "beep"
sound after power is connected work.
- Use remote control point to receive window and push
any button, various function work accordingly.
ON/OFF button:
- Firstly push ON/OFF button, the indicator light is on.
- Secondly push ON/OFF button, the wind speed is in the
low level by default. Meanwhile, the indoor temperature
shows on the panel.
Thirdly push ON/OFF button, all stop working, all indicator
lights off.
Speed button:
- Firstly push speed button, the wing speed is in the me-
dium level
- Secondly push speed button, the wind speed is in the
high level
- Thirdly push speed button, the wind speed returns to
the low level.
Mode button:
- Natural mode → Sleep mode → Normal mode
Natural mode : The wind imitate the blow of natural wind
based on strong and soft wind.
Sleep mode: the first half hour after running as strong and
soft natural wind, it becomes med natural wind and the
second half hour it changes to soft natural wind until the
end of preset time.
Normal mode: The wind blow based on Low/Med/High
speed.
Mist function:
- Mist function can be used separately, or worked together
with the fan.
- Firstly push Mist button, the mist spray in low volume.
Secondly push Mist button, the mist spray in medium
volume.
- Thirdly push Mist button, the mist spray in high volume.
- Note: While the mist function work normally, the indicator
light on the body shell is blue, while the water is lacking,
the indicator light is red.
Oscillation function:
- The oscillation function makes it possible to direct the
flow from the apparatus so that it automatically alternates
over a range of 75º
- To activate this function, push the OSC button. The ye-
llow light of OSC on .
- Press it again to stop oscillation, yellow light of Osc off.
Ionic function:
- Mist function can be used separately, or worked together
Notice vb 02-New.indb 10
with the fan.
- The appliance can generate negative ions generated
by the ionizer emanate from the unit throughout the room
and cause dust, pollen, pet dander etc to clump together
and drop out of the air.
- Push the ion button, green light of Ion function on,
- Push it again to stop working, the green light of Ion
function off.
Mosquito repellent function
- Mosquito repellent function can be used separately, or
worked together with the fan.
- Put the mosquito repellent tablet (not included with the
product) into its hole on the body rear shell.
- Push Mosquito button red light of mosquito repellent on,
to avoid the mosquitoes annoy.
- Push it again to stop working, red light of mosquito re-
pellent off.
Note:
- Turn off the power when you replacing the mosquito
repellent tablet, wait for 10 minutes then replacement in
order to avoid burns or electric shock.
- Do put the mosquito repellent tablet in contact with eyes
or mouth. If put in mouth by accident, wash mouth and
seek medical care immediately.
Timer function:
- The appliance's operating time can be controlled.
- It can be set the fan running time between 1-12hours
and switches the fan off after preset time,
- To set a timer of 1 hour, push Timer button one time.
Meanwhile, the indoor temperature display is replaced by
timer display of 01H.
- To set 12 hours of running time, you need to press 12
times and the number of hours displayed on the panel will
change every time.
- After setting 12 hours timer, push TIMER button again,
timer is cancelled. Once timer cancelled, the indoor tem-
perature will be displayed on the panel.
- While setting timer, the timer hour and the indoor tempe-
rature will be displayed on the panel every 5 seconds by
turn. And the number of hours displayed on the panel will
decrease per hour.
- The time programmed or remaining time will appear on
the display (N).
Once you have finished using the appliance:
- Turn the appliance off using the on/off button.
- Unplug the appliance from the mains.
- Clean the appliance.
Cleaning
- Disconnect the appliance from the mains and allow it to
cool before undertaking any cleaning task.
- Clean the equipment with a damp cloth with a few drops
of washing-up liquid and then dry.
- Do not use solvents, or products with an acid or base
pH such as bleach, or abrasive products, for cleaning the
appliance.
29/04/2016 09:21
Publicidad
