STAMOS MIG Serie Manual De Instrucciones página 24

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 60
EN
Plate thick-
Welding
Solder wire
Welding
ness t(mm)
Angle size l
diameter
current (A)
(mm)
(mm)
1,0
2,5 - 3,0
0,8 - 0,9
70 - 80
1,2
2,5 - 3,0
1,0
70 - 100
1,6
2,5 - 3,0
1,0 - 1,2
90 - 120
2,0
3,0 - 3,5
1,0 - 1,2
100 - 130
2,3
2,5 - 3,0
1,0 - 1,2
120 - 140
3,2
3,0 - 4,0
1,0 - 1,2
130 - 170
4,5
4,0 - 4,5
1,2
190 - 230
Fillet Weld Seam in vertical position
Plate thick-
Welding
Solder wire
Welding
ness t(mm)
Angle size l
diameter
current (A)
(mm)
(mm)
1,2
2,5 - 3,0
1,0
70 - 100
1,6
2,5 - 3,0
1,0 - 1,2
90 - 120
2,0
3,0 - 3,5
1,0 - 1,2
100 - 130
2,3
3,0 - 3,5
1,0 - 1,2
120 - 140
3,2
3,0 - 4,0
1,0 - 1,2
130 - 170
4,5
4,0 - 4,5
1,2
200 - 250
46
Welding
Welding
Gas flow (L/
voltage (V)
Speed (cm/
Min)
Min.)
17 - 18
50 - 60
10 - 15
18 - 19
50 - 60
10 - 15
18 - 20
50 - 60
10 - 15
19 - 20
50 - 60
10 - 20
19 - 21
50 - 60
10 - 20
19 - 21
45 - 55
10 - 20
22 - 24
45 - 55
10 - 20
Welding
Welding
Gas flow (L/
voltage (V)
Speed (cm/
Min)
Min.)
18 - 19
50 - 60
10 - 15
19 - 20
50 - 60
10 - 15
19 - 20
50 - 60
10 - 20
19 - 21
50 - 60
10 - 20
22 - 22
45 - 55
10 - 20
23 - 26
45 - 55
10 - 20
EN
Lap Welding
Plate thick-
Welding
Solder wire
Welding
ness t(mm)
location
diameter
current (A)
(mm)
0,8
A
0,8 - 0,9
60 - 70
1,2
A
1,0
80 - 100
1,6
A
1,0 - 1,2
100 - 120
2,0
A / B
1,0 - 1,2
100 - 130
2,3
B
1,0 - 1,2
120 - 140
3,2
B
1,0 - 1,2
130 - 160
4,5
B
1,2
150 - 200
TROUBLESHOOTING
Disturbance, cause
Volatile or unstable arc?
Incorrect welding voltage adjustment
Too much/too little wire
Workpiece clamp loose or large con-
tact resistance (rust, paint)
Contact nozzle worn or incorrect
diameter
Incorrect gas quantity set
Workpiece not clean in the weld area
47
Welding
Welding
Gas flow (L/
voltage (V)
speed (cm/
min)
min)
16 - 17
40 - 45
10 - 15
18 - 19
45 - 55
10 - 15
18 - 20
45 - 55
10 - 15
18 - 20
45 - 55
10 - 20
19 - 21
45 - 50
10 - 20
19 - 22
45 - 50
10 - 20
21 - 24
40 - 45
10 - 20
Solution
Correct adjustment on voltage regu-
lator
Correct adjustment on wire feed
regulator
Ensure good contact between the
workpiece and the workpiece clamp
Replace
Set the amount of gas
Remove paint, rust, grease etc.

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Mag serieMma serieS-mig 250cS-mig 350c

Tabla de contenido