Disposing Of Packaging - STAMOS MIG Serie Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 60
EN
WARNING
INHALATION HAZARD: Welding and Plasma Cutting Produce
TOXIC FUMES.
Exposure to welding or cutting exhaust fumes can increase the risk of developing
certain cancers, such as cancer of the larynx and lung cancer. Also, some diseases
that may be linked to exposure to welding or plasma cutting exhaust fumes are:
a.
Early onset of Parkinson's Disease
b.
Heart disease
c.
Ulcers
d.
Damage to the reproductive organs
e.
Inflammation of the small intestine or stomach
f.
Kidney damage
g.
Respiratory diseases such as emphysema, bronchitis, or pneumonia
Use natural or forced air ventilation and wear a respirator approved by NIOSH
to protect against the fumes produced to reduce the risk of developing the above
illnesses.
9.
Avoid overexposure to fumes and gases. Always keep your head out of the
fumes. Do not breathe the fumes. Use enough ventilation or exhaust, or
both, to keep fumes and gases from your breathing zone and general area.
Where ventilation is questionable, have a qualified technician take an air samp-
ling to determine the need for corrective measures. Use mechanical ventilation
to improve air quality. If engineering controls are not feasible, use an approved
respirator.
Work in a confined area only if it is well ventilated, or while wearing an airsup-
plied respirator.
Follow OSHA guidelines for Permissible Exposure Limits (PEL's) for various
fumes and gases.
Follow the American Conference of Governmental Industrial Hygienists re-
commendations for Threshold Limit Values (TLV's) for fumes and gases.
Have a recognized specialist in Industrial Hygiene or Environmental Services
check the operation and air quality and make recommendations for the specific
welding or cutting situation.
10.
Always keep hoses away from welding/cutting spot. Examine all hoses and
cables for cuts, burns, or worn areas before each use. If any damaged areas
are found, replace the hoses or cables immediately.
11.
Read and understand all instructions and safety precautions as outlined in
the manufacturer's Manual for the material you will weld or cut.
12.
Proper cylinder care. Secure cylinders to a cart, wall, or post, to prevent
them from falling. All cylinders should be used and stored in an upright po-
sition. Never dropor strike a cylinder. Do not use cylinders that have been
dented. Cylinder caps should be used when moving or storing cylinders. Em-
pty cylinders should be kept in specified areas and clearly marked "empty."
30
EN
13.
Never use oil or grease on any inlet connector, outlet connector, or cylinder
valves.
14.
Use only supplied Torch on this Inverter Air Plasma Cutter. Using compo-
nents from other systems may cause personal injury and damage compo-
nents within.
15.
People with pacemakers should consult their physician(s) before using this
product. Electromagnetic fields in close proximity to a heart pacemaker
could cause interference to, or failure of the pacemaker.
16.
USE PROPER EXTENSION CORD. Make sure your extension cord is in
good condition. When using an extension cord, be sure to sue one heavy
enough to carry the current your product will draw. An undersized cord will
cause a drop in line voltage resulting in loss of power and overheating. A 50
foot extension cord must be at least 12 gauges in diameter, and a 100 foot
extension cord must be at least 10 gauges in diameter. If in doubt, use the
next heavier gauge. The smaller the gauge number, the heavier the cord.
CONSIGNING THE SCALE
Checking packaging upon consignment
When you received the goods proceed with opening the packaging if there are no
signs of damage. If there are signs of damage on packaging please send a detailed list
and report of all damage to the goods to your local representative within 3 days
after delivering.

Disposing of packaging

The various items used for packaging (cardboard, plastic straps, polyurethane
foam) should be conserved, so that the device can be sent back to the service
center in best conditions in case of problem.
31

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Mag serieMma serieS-mig 250cS-mig 350c

Tabla de contenido