mundoclima MUPO-12-H9 Manual De Instalación Y Usuario página 39

Operation
Swing button
Used to initiate the Auto swing feature. When
the operation is ON, press the SWING button
can stop the louver at the desired angle.
Wireless button
Used to initiate the Wireless function. For the
first time to use Wireless function, press and
hold the swing button for 3 seconds to initiate the
Wireless connection mode. The LED DISPLAY
shows 'AP' to indicate you can set Wireless
connection. If connection(router) is successful
within 8 minutes, the unit will exit Wireless
connection mode automatically and the Wireless
indicator illuminates. If connection is failure
within 8 minutes, the unit exits Wireless
connection mode automatically. After Wireless
connection is successful, you can press and
hold SWING and DOWN (-) buttons at the same
time for 3 seconds to turn off Wireless function
and the LED DISPLAY shows 'OF' for 3 seconds,
press SWING and UP(+) buttons at the same
time to turn on Wireless function and the LED
DISPLAY shows 'ON' for 3 seconds.
NOTE: When you restart the Wireless function,
it may take a period of time to connect to the
network automatically.
Timer button
Used to initiate the AUTO ON start time and
AUTO OFF stop time program, in conjuction
with the + & - buttons. The timer on/off indicator
light illuminates under the timer on/off settings.
Mode button
Selects the appropriate operating mode. Each
time you press the button, a mode is selected in
a sequence that goes from AUTO), COOL, DRY,
FAN and HEAT (cooling only models without).
The mode indicator light illuminates under the
different mode settings.
Up (+) and Down (-) buttons
Used to adjust (increasing/decreasing)
temperature settings in 1°C/1°F (or 2 °F)
increments in a range of 17°C/62°F to
30°C/86°F (or 88°F) or the TIMER setting in a
range of 0~24hrs.
NOTE: The control is capable of displaying
temperature in degrees Fahrenheit or
degrees Celsius. To convert from one to the
other, press and hold the Up and Down
buttons at the same time for 3 seconds.
(optional)
Fan/Ion button(Ion is optional)
Control the fan speed. Press to select the fan
speed in four steps-LOW, MED, HIGH and AUTO.
The fan speed indicator light illuminates under
different fan settings. When select AUTO fan
speed, all the fan indicator lights turn dark. On
some models, when select AUTO fan speed, all
the fan indicator lights illumiante(optional).
NOTE: Press this button for 3 seconds to initiate
ION feature. The ion generator is energized and
will help to remove pollen and impurities from the
air, and trap them in the filter. Press it for 3
seconds again to stop the ION feature.
Sleep(Eco) button
Used to initiate the SLEEP/ECO operation.
Power button
Power switch on/off.
LED display
Shows the set temperature in °C or °F("°F"
no display for some models) and the Auto-timer
settings. While on DRY and FAN modes, it
shows the room temperature.
Shows Error codes and protection code:
E1-Room temperature sensor error.
E2-Evaporator temperature sensor error.
E3-Condenser temperature sensor error
(on some models).
E4-Display panel communication error.
EC-Refrigerant leakage detection malfunction
(on some models).
P1-Bottom tray is full--Connect the drain hose
and drain the collected water away.If
protection repeats,call for service.
Note: When one of the above malfunctions
occurs, turn off the unit, and check for any
obstructions. Restart the unit, if the
malfunction is still present, turn off the unit
and unplug the power cord. Contact the
manufacturer or its service agents or a similar
qualified person for service.
Exhaust hose installation
The exhaust hose and adaptor must be installed or
removed in accordance with the usage mode.
For COOL,HEAT(heat pump type) or AUTO mode
must be installed exhaust hose.
For FAN,DEHUMIDIIFY or HEAT(electrical heat
type) mode must be removed exhaust hose.
39