Ryobi RBC30SET Manual De Utilización página 33

EN
FR DE ES
HEAD
See Figures 5
Use 2.4mm diameter monofilament line.
Stop the engine and disconnect the spark plug wire.
Q
Cut one piece of line approximately 6.0 meters in
Q
length.
Rotate knob on line trimmer head until line on knob
Q
aligns with arrows on top of line trimmer head.
Insert one end of line into eyelet located on the side
Q
of the line trimmer head and push until line comes
out through the eyelet on the other side. Continue
to push line through the line trimmer head until the
middle section of the line is inside the line trimmer
head and line outside the line trimmer head is evenly
divided on each side.
Rotate the knob on the line trimmer head to wind the
Q
line. If using the RLT30CET curved shaft line trimmer
attachment, the knob should be rotated clockwise. If
using a straight shaft attachment, the knob should be
rotated counterclockwise.
Wind the line until approximately 20cm remains
Q
protruding from the line trimmer head.
NOTE: Depending on the type of fuel used, the type
and amount of lubricant used, and/or your operating
conditions, the exhaust port, muffler, and/or spark
arrestor screen may become blocked with carbon
deposits. If you notice a power loss with your petrol
powered tool, you may need to remove these deposits
to restore performance. We highly recommend that only
qualified service technicians perform this service.
The spark arrestor must be cleaned or replaced every
50 hours or yearly to ensure proper performance of your
product. Spark arrestors may be in different locations
depending on the model purchased. Please contact
your nearest service dealer for the location of the spark
arrestor for your model.
IDLE SPEED ADJUSTMENT
See Figure 17.
If the cutting attachment turns at idle, the idle speed
screw needs adjusting on the engine. Turn the idle speed
screw counter clockwise to reduce the idle RPM and
stop the cutting attachment movement. If the cutting
attachment still moves at idle speed, contact a service
dealer for adjustment and discontinue use until the repair
is made.
WARNING:
The cutting attachment should never turn at idle.
Turn the idle speed screw counter clockwise
to reduce the idle RPM and stop the cutting
attachment, or contact a service dealer for
adjustment and discontinue use until the repair
is made. Serious personal injury may result from
IT PT NL SV DA
English (original instructions)
NO FI HU CS RU
the cutting attachment turning at idle.
CLEANING AIR FILTER SCREEN
See Figures 18 - 19.
For proper performance and long life, keep air filter
Q
screen clean.
Remove the air filter cover by pushing down on the
Q
latch with your thumb while gently pulling on the
cover.
Brush the air filter screen lightly to clean.
Q
Replace the air filter cover by inserting the tabs on
Q
the bottom of the cover into the slots on the air filter
base; push the cover up until it latches securely in
place.
FUEL CAP
WARNING:
A leaking fuel cap is a fire hazard and must be
replaced immediately.
The fuel cap contains a non-serviceable filter and a
check valve. A clogged fuel filter will cause poor engine
performance. If performance improves when the fuel cap
is loosened, check valve may be faulty or filter clogged.
Replace fuel cap if required.
SPARK PLUG REPLACEMENT
This engine uses a Champion RCJ-6Y or NGK BPMR7A
spark plug with 6.35mm electrode gap. Use an exact
replacement and replace annually.
STORING THE PRODUCT
Clean all foreign material from the product. Store
Q
idle unit indoors in a dry, well-ventilated area that is
inaccessible to children. Keep away from corrosive
agents such as garden chemicals. Fit the blade
guard to the blade.
When storing 1 month or longer:
Drain all fuel from tank into a container approved for
Q
petrol. Run engine until it stops.
30
RO PL SL HR ET
MAINTENANCE
LT LV SK BG