Setting The Clock; Making Coffee - Morphy Richards 47110 Manual Del Usuario

47110MEE Rev1:Layout 2
7 If no buttons are pressed for 2 seconds the coffee maker
will begin brewing. The water gauge will illuminate. The hot
water will start to flow through the coffee grounds and into
the jug as coffee for you to enjoy.
• When the brewing process is complete, the power light and
the internal water tank illumination switches off. We
recommend you switch off your coffee maker at the mains
as soon as brewing is complete.
• The thermal carafe · will keep the coffee warm in the jug
for up to four hours.
• The anti drip valve will prevent any remaining coffee
dripping onto the base recess during serving.
• We suggest consuming your coffee within four hours, after
this time we suggest brewing another jug of fresh coffee.
• WARNING: The coffee maker is hot and will remain hot for
some time after switching off.
NOTE:
• To cancel brewing press the appropriate on/off button once.
• Remember to turn off the machine at the mains when you
have finished.
• Allow the unit to cool.
• Remove the permanent filter and empty the used coffee
grounds. Wash the filter immediately and dry thoroughly.
DIGITAL INTERFACE VERSION

Setting the clock

• When the machine is plugged in, the display will flash
00:00 dimly.
• To set the time, press the hour button È and minute
button Í to reach the desired time.
The clock will be reset each time the product is unplugged
at the wall.
NOTE: The clock is a 24 hour clock.

Making coffee

1 Press the Release button › to remove the water reservoir
‡ and fill with the required amount of water using the level
indicator fl as a guide. The water level indicator is marked in
cups A. Do not overfill past the 10 cups mark.
2 Press the coffee filter release button ‹ to open the filter
compartment. The compartment will automatically open.
3 Ensure the filter is sitting properly in the filter holder C.
Spoon the required amount of ground filter coffee into the
mesh filter ‰, spreading evenly D. We suggest two level
measuring spoon for every cup (20 spoons maximum).
4 Close the compartment. Ensure the filter compartment is
closed and latched properly, otherwise the machine will not
function correctly.
5 Slide the carafe · into the coffee maker, because there is no
hot plate, please ensure the carafe sits correctly on the base
recess.
• Ensure the jug lid is fully closed by turning the lid lock
6
24/8/09 15:31 Page 6
clockwise ‚, this ensures the maximum temperature is
maintained in the jug. To ensure the coffee is kept as warm as
possible, we advise you rinse your thermal carafe in hot water
before use.
• Please note the jug lid must be in place during the brewing
process; otherwise the non-drip valve will not open, causing
the filter to flood.
6 Plug the filter coffee maker in at the wall socket and switch
on, if applicable, press either the full carafe power on/off
button ⁄ or the half carafe power on off button ¤,
depending on the number of cups required. The relevant
button will illuminate and the selection will be highlighted on
the display E.
7 If no buttons are pressed for 2 seconds the coffee maker will
begin brewing. The water gauge will illuminate. The hot water
will start to flow through the coffee grounds and into the jug
as coffee for you to enjoy.
• When the brewing process is complete, the product remains
on, we recommend you switch off your coffee maker as soon
as brewing is complete.
• The thermal carafe · will keep the coffee warm in the jug for
up to four hours.
• The anti drip valve will prevent any remaining coffee dripping
onto the base recess during serving.
• We suggest consuming your coffee within four hours, after
this time we suggest brewing another jug of fresh coffee.
• WARNING: The coffee maker is hot and will remain hot for
some time after switching off.
NOTE:
• To cancel brewing press the on/off button once.
• Remember to turn off the machine when you have finished.
• Allow the unit to cool.
• Remove the permanent filter and empty the used coffee
grounds. Wash the filter immediately and dry thoroughly.
Auto brew mode
An automatic brewing start time can be set when the machine
is either; switched on, on standby or while already brewing.
1 Press the Programme button Ë, the display will change to
show the previous set time and cup selection (flashing). If no
previous setting has been made, or if the machine has been
unplugged since the last setting, the default setting will be
shown (12:00 and full carafe).
2 Press either the full carafe power on/off button ⁄ or the half
carafe power on off button ¤, depending on the number of
cups required. The relevant button will illuminate. The icon
will be highlighted on the display.
3 Press the hour È and minute Í buttons to get the desired
time. The start time will stop flashing.
NOTE:
• The programming mode indicator continues to flash to show
the display is still in programming mode.
4 If the programme button Ë is pressed again or if no buttons