Tabla de contenido
Publicidad
Enlaces rápidos
PRINT SPECS FOR ATON VOLUME CONTROL
MANUAL
INSTR, INSTL, ATON AVL100SL and AVLR100
LINEAR P/N 9901023 REV: A
INK: BLACK
MATERIAL: 60 LB WHITE COATED PAPER
PAGES: 36 PAGES
SCALE: 1-1
SIZE: 7.0 x 4.5 inches
FOLD TO 3.5 X 4.5
FOLDING: ALBUM FOLD CENTER STAPLE
NOTE: ARTWORK CREATED BY ELAN HOME
SYSTEMS
THIS MANUAL MUST BE RoHS COMPLIANT
DO NOT PRINT THIS PAGE, MANUAL STARTS ON
FOLLOWING PAGE
Publicidad
Tabla de contenido
Manuales relacionados para ATON AVC100SL
Resumen de contenidos para ATON AVC100SL
- Página 1 PRINT SPECS FOR ATON VOLUME CONTROL MANUAL INSTR, INSTL, ATON AVL100SL and AVLR100 LINEAR P/N 9901023 REV: A INK: BLACK MATERIAL: 60 LB WHITE COATED PAPER PAGES: 36 PAGES SCALE: 1-1 SIZE: 7.0 x 4.5 inches FOLD TO 3.5 X 4.5...
- Página 2 STEREO VOLUME CONTROLS AVC100SL 100 Watt High Power Stereo Sliding Volume Control AVC100R 100 Watt High Power Stereo Rotary Knob Volume Control INSTALLATION MANUAL P/N: 9901023 REV A...
- Página 3 This ATON Volume Control is NTRL certified to comply with local building codes. Use Class 2 wiring and methods per National Electrical Code NFPA70. Install in a Listed electrical box.
-
Página 4: Tabla De Contenido
VOLUME CONTROL INSTALLATION MANUAL Contents Introduction ............2 Features ..............3 Rough-In ............4 Wiring ..............5 Impedance Match Settings ......7-8 Installation ..........9-10 Operation ............11 Troubleshooting ..........12 Specifications ..........13 Warranty ............14 Page 1 ©ATON 2010 • All rights reserved. -
Página 5: Introduction
VOLUME CONTROL INSTALLATION MANUAL Introduction The ATON AVC100SL and AVC100R High Power Stereo Volume Control is a twelve step stereo Volume Control with variable Impedance Match settings. These Volume Controls are designed to connect speakers to amplifiers with power ratings up to 100 Watts RMS. Based on... -
Página 6: Features
• PTC-Thermal Protection Circuit: When the PTC detects problems such as, too much power, crossed speaker wiring, or improper impedance, the circuit will open, protecting the volume control. When the problem has been corrected, the circuit will close and resume operation. Page 3 ©ATON 2010 • All rights reserved. -
Página 7: Rough-In
VOLUME CONTROL INSTALLATION MANUAL Rough-In The AVC100SL/AVC100R will into the majority of single-gang boxes. This Volume Control should not be mounted in the same rough-in box as primary or mains volt devices, i.e. 110v, 240v--this can cause undesirable noise in the speakers. High Wattage light dimmers can also cause noise issues. -
Página 8: Wiring
VOLUME CONTROL INSTALLATION MANUAL Wiring The AVC100SL / AVC100R can accommodate from 14 to 24 guage speaker wire. Typical installations will use 16 or 18 guage stranded copper wire, while longer runs (greater than 80 feet.) should use 14 guage wires. In-wall runs should utilize twisted pair wiring. - Página 9 VOLUME CONTROL INSTALLATION MANUAL AVC100R Impedance Match Switch From Amplifier To Speakers 8X 4X 2X 1X Impedance Match Switch Page 6 © ATON 2010 • All rights reserved.
-
Página 10: Impedance Match Settings
VOLUME CONTROL INSTALLATION MANUAL Impedance Match Settings Switch and Jumper settings on the AVC100SL and AVC100Rdetermine the Impedance Match settings. See diagram for location of Switches and Jump- ers. These setting positions depend on three things: 1. The minimum impedance rating of the amplifier used 2. - Página 11 Both Switches MUST be in Same Position Never create settings that cause the amplifier to see an impedance below its minimum impedance rating as this can cause damage to the amplifier. Page 8 © ATON 2010 • All rights reserved.
-
Página 12: Installation
7. Carefully place the Volume Control in the rough-in box making sure not to put strain on the speaker / amplifier connections. 8. Insert two 1" screws into the mounting holes of the AVC100SL / AVC100R to mount the unit into the rough-in box. Tighten these screws until the unit is at the proper depth to mount flush with the wall. -
Página 13: Checking The Installation
2. Make sure amplifier is not powered up whenmaking connections or testing. DO NOT REVERSE THE AMPLIFIER INPUT AND SPEAKER OUTPUT CONNECTIONS! THIS CAN RESULT IN DAMAGE TO EQUIPMENT AND/OR PROPERTY. Page 10 © ATON 2010 • All rights reserved. -
Página 14: Operation
1. When using a receiver or integrated amplifier with its own Volume functions, turn the Volume all the way down. 2. Turn Volume all the way up on the AVC100SL / AVC100R, and then slowly adjust the volume on the receiver until a comfortable listening level is obtained. -
Página 15: Troubleshooting
See Imp. Match Section ance Match settings starting on pg.8 and set switches correctly 4. Incorrect assign- Isolate to source or room ment of left/right and correct source RCA cables or speaker cables Page 12 © ATON 2010 • All rights reserved. -
Página 16: Specifications
VOLUME CONTROL INSTALLATION MANUAL SPECIFICATIONS AVC100SL Power Rating--Nominal ....100 Watts RMS per Channel AVC100R Power Rating--Nominal ....100 Watts RMS per Channel Frequency Response ........20-20KHz +/- 0.5dB @ 8 Ohms Total Harmonic Distortion ..............< 1% Impedance Settings ..............1X/2X/4X/8X Minimum Speaker Load .............. -
Página 17: Warranty
(c) to installed equipment which is not installed to ATON’s specifications, (d) to equip- ment which shall have been repaired or altered by others than ATON, (e) to equipment which shall have been subjected to negligence, accident, or damage by circumstances beyond ATON’s control, including, but not limited to, lightning, flood, electrical surge,... - Página 30 1X 2X 4X 8X...
- Página 31 1X 2X 4X 8X...