Preparation For Use; Fitting Instructions - 3M 6000 Serie Manual De Instrucciones

frequency of change depends on usage time and
the concentration of contaminant.
• For more information call the 3M Health & Safety
Helpline on 0870 60 800 60 (UK) or 1 800 320 500
(Ireland).
• If using with a 3M™ Air Supply Unit:
r • At very high work rates, the pressure in the
facepiece may become negative at peak inhalation
rs. flow. Adjust equipment as appropriate or consider
an alternative form of respiratory protective device.
• If using in Supplied Air mode, ensure that:
• The source of the air supply is known.
• The purity of the air supply is known.
• The air supply is of a breathable quality to
EN12021.
If during use the air supply stops or is reduced,
et vacate the contaminated area immediately and
investigate the cause.
• Take care to prevent the breathing tube from
becoming looped around protruding objects.
• These products do not supply oxygen.
NOTES REGARDING ALLERGIC
REACTIONS
Materials which may come into contact with the
wearer's skin are not known to cause allergic
reactions to the majority of individuals.
These products do not contain components made
from natural rubber latex.

PREPARATION FOR USE

s,
Inspect the package contents for shipping damage
and ensure all components are present.
Check apparatus is complete, undamaged and
correctly assembled. Any damaged or defective
parts must be replaced with original 3M spare parts
at
before use.
Inspection
The following inspection procedure is
recommended before use:
e
1. Check the facepiece for cracks, tears and dirt. Be
certain the facepiece, especially the face seal area,
is not distorted. The material must be pliable – not
stiff.
™
2. Examine the inhalation valves for cracks or tears.
Lift valves and inspect valve seat for dirt or cracks.
3. Ensure that the head straps are intact and have
good elasticity.
4. Examine all plastic parts for signs of cracks or
fatigue.
5. Make sure all gaskets are properly seated.
6. Remove the exhalation valve cover and examine
the exhalation valve and valve seat for signs of dirt,
distortion, cracks or tears. Replace the exhalation
valve cover.
7. Inspect lens for any damage that may impair
respirator performance or vision.
ASSEMBLY INSTRUCTIONS
See appropriate User Instructions for assembly
instructions (e.g. 3M™ Filter/3M™ Air Supply Unit).

FITTING INSTRUCTIONS

Select most appropriate size from the 3 sizes of the
facepiece available (S / M / L). Fitting Instructions
must be followed each time the product is worn.
DONNING
1. Fully loosen all 4 head straps and put straps over
front of facepiece.
2. If necessary, pull hair back out of facepiece
sealing area.
3. Place chin in respirator chin cup and make sure
that respirator is centred on your face.
4. Pull head harness over your head (Figure 1).
Remove any bumps or kinks in the head harness
and ensure straps are flat to the head.
5. Whilst holding the mask in place with one hand,
tighten each strap evenly a little at a time, starting
the neck straps, followed by the forehead straps.
Repeat until the mask feels secure on the face.
(Figure 2). DO NOT OVERTIGHTEN.
6. Ensure that there are no creases or gaps around
facepiece perimeter. Figure 3 shows a poorly fitted
mask with creases around the face piece,
WARNING Such creases may impact fit. Use of a
mirror or the help of a colleague is recommended.
Readjust straps and/or reposition facepiece as
necessary.
Perform a positive and/or negative pressure seal
check.
SEAL CHECK
• Positive Pressure User Seal Check (for all
approved configurations) (all Filters except 3M™
6035 /6038/ 2000 Series Filters).
Place palm of hand over exhalation valve cover and
exhale gently. Figure 4.
If the facepiece bulges slightly and no air leaks are
detected between the face and the facepiece, a
proper seal has been obtained.
6
If a
the
str
Re
• N
60
Pre
the
filte
ho
fac
ac
rep
re-
the
If y
en
Qu
Fo
ple
D
^
Su
ha
1.
2.
the
3.
dis
reg
NO
tha
a s
pro
co
de
M
Ma
ca
res
lim
(Se
the
^
mo
he
ins
mo
de