Preliminary Inspection; Product Information - Franklin Electric FPS VR Serie Manual De Uso E Instalación

Electrobombas multietapa verticales 50 hz

Tabla de contenido

Idiomas disponibles

Use and installation instruction manual

Personal Protective Equipment (PPE)

During installation, routine and extraordinary maintenance, decommissioning

and disposal, use the personal protective equipment (PPE) specified below.

Additional PPE may be necessary, depending on the working conditions

By properly using PPE, any residual health risks may be reduced.

Wear safety gloves

Protect your eyesight with safety goggles

Wear steel toe cap safety shoes, insulated from the ground

Wear a respirator if there is a risk of toxic, irritating or suffocating fumes

Suitable clothing

During maintenance operations and in any case when the machine is

running in various modes, including its normal operating mode, avoid any

clothing or accessories that may get entangled in the moving parts of the

machine.

2 PRODUCT INFORMATION

The product model, main service specifications and serial number are shown on the rating plate. It is important to provide these details when requesting service or

support and spare parts. Refer to fig. A3 for the position of the rating plate (attached).

The product model is identified by an alphanumeric code shown on the rating plate. The meaning of the characters in the code is explained in Fig. 1. The product can be

identified via not only a code but also a serial number (Fig. 2). This information can also be found on the label applied to the cover of this instruction manual.

Pump identification code

(Fig. 1)

3 VR 07

Tensione (Fase)

Voltage (Phase)

"2" (230 V, 1-Phase, 50 Hz) "B" (230/400 V, 3-Phase, 50 Hz)

E cenza

Efficency

"D" (Premiun / ODP)

Velocità rotazione (Hz)

Speed (Hz)

"5" (3000 rpm, 50 Hz); "7" (1500 rpm, 50 Hz);

Dimensioni e potenza motore

Frame size and motor power

Tipo motore

Motor type

"A" (Nema)

Tenuta meccanica

Mechanical seal

"1" (QBE)

"5" (UUE)

Connessione

Connection "F" (Round) "T" (Oval)

Materiale

Material

"H" (304SS) "N" (316SS) "G" (CI+304SS)

Impeller trim "00" (No Trim)

Girante ridotta

No. Stadi

No. Stages

Pump model

Modello pompa

Rated flow [m³/h]

Portata nominale [m /h]

Declaration of conformity

The declaration of conformity, including the rules and regulations considered in

the design phase, is shown at the end of the manual.

Noise emission

Noise emission is mainly influenced by the size of the motor and pump. For

pumps supplied without motors, refer to the noise emission declared by the

motor manufacturer and consider a 3-5 dB increase. For complete electric pumps,

refer to fig. A2 attached. The specified values refer to a 1 m distance from the

machine. Operators working long shifts in close proximity to the machine must

protect themselves with hearing aids that are appropriate to the sound pressure

and exposure time.

1 PRELIMINARY INSPECTION

1.1 Delivery and packaging

The product is supplied in its original packaging, which includes this instruction

manual, and must remain packed until it is installed. The packed product must be

stored away from atmospheric agents. Remove the appliance from the packaging

and check that it is intact. Also check whether the rating plate details match the

desired ones. To properly read the rating plate, refer to the instructions in this

manual. In case of any discrepancies, contact the supplier immediately, specifying

the nature of the defects.

If in doubt about the machine safety or integrity, do not use it and contact

a professional service centre.

"4" (460 , 3-Phase, 60 Hz) "6" (220, 1-Phase, 60 Hz)

"D" (Premiun / ODP)

"X" (Premium / X-Proof)

"6" (3600 rpm, 60 Hz) "8" (1800 rpm, 60 Hz)

"Q" (0,25 KW / 0,33 HP, Nema 56C)

"A" (0,37 KW / 0,5 HP, Nema 56C / IEC MEC71)

"B" (0,55 KW / 0,75 HP, Nema 56C / IEC MEC71) "W" (11 KW / 15 HP, Nema 210TC / IEC MEC160)

"B" (0,55 KW / 0,75 HP, Nema 56C / IEC MEC71)

"C" (0,75 KW / 1 HP, Nema 56C / IEC MEC80)

"D" (1,1 KW / 1,5 HP, Nema 56C / IEC MEC80)

"E" (1,5 KW / 2 HP, Nema 56C / IEC MEC90)

"E" (1,5 KW / 2 HP, Nema 56C / IEC MEC90) "

"Y" (1,5 KW / 2 HP, Nema 180TC)

"F" (2,2 KW / 3 HP, Nema 56C / IEC MEC90)

"U" (2,2 KW / 3 HP, Nema 180TC)

"I" (3 KW / 4 HP, IEC MEC100)

"G" (3,7 KW / 5 HP, Nema 180TC)

"O" (4 KW / 5,5 HP, IEC MEC112)

"V" (5,5 KW / 7,5 HP, Nema 180TC / IEC MEC132)

"V" (5,5 KW / 7,5 HP, Nema 180TC / IEC MEC132) "T" (55 KW / 75 HP, Nema 360TSC)

"A" (Nema) "B" (IEC)

"B" (IEC)

"1" (QBE)

"2" (QQE)

"3" (QQV)

"2" (QQE)

"5" (UUE)

"6" (UUV)

"7" (BQQV)

"F" (Tonda) "T" (Ovale)

"V" (Victaulic) "C" (Clamp) "H" (Victaulic, alta pressione)

"V" (Grooved)

"H" (304SS) "N" (316SS) "G" (CI+304SS)

"00" (Non ridotta)

"A1" (1A)

"A2" (2A)

"D" (220/380, 3-Phase, 60 Hz)

"C" (400/690 V, 3-Phase, 50 Hz)

"E" (Premium / TEFC)

"H" (5,5 KW / 7,5 HP, Nema 210TC)

"J" (7,5 KW / 10 HP, Nema 210TC / IEC MEC132)

"W" (11 KW / 15 HP, Nema 210TC / IEC MEC160)

"K" (11 KW / 15 HP, Nema 250TC)

"L" (15 KW / 20 HP, Nema 250TC / IEC MEC160)

"X" (18,5 KW / 25 HP, Nema 250TC / IEC MEC160)

X" (18,5 KW / 25 HP, Nema 250TC / IEC MEC160)

"M" (18,5 KW / 25 HP, Nema 280TSC)

"N" (22 KW / 30 HP, Nema 280TSC / IEC MEC180)

"Z" (30 KW / 40 HP, Nema 280TSC / IEC MEC200)

"P" (30 KW / 40 HP, Nema 320TSC)

"R" (37 KW / 50 HP, Nema 320TSC / IEC MEC200)

"S" (45 KW / 60 HP, Nema 360TSC / IEC MEC225)

"T" (55 KW / 75 HP, Nema 360TSC)

"4" (QBV)

"3" (QQV)

"4" (QBV)

"7" (BQQV)

"C" (Clamp)

"H" (Grooved, High Pressure)

"P" (316SS)

ENGLISH

"N" (Nema)

Tabla de Contenido

Tabla de contenido

Preliminary Inspection; Product Information - Franklin Electric FPS VR Serie Manual De Uso E Instalación

Idiomas disponibles

2 PRODUCT INFORMATION

1 PRELIMINARY INSPECTION

Manuales relacionados para Franklin Electric FPS VR Serie

Contenido relacionado para Franklin Electric FPS VR Serie

Tabla de contenido