Tabla de contenido
Publicidad
English
The user instructions apply to several models, for this
reason there may be some differences
given, according to the type of the appliance..
1 Protecting the environment / advice for disposal
Packing
serves to protect the appliance during transportation and
recyclable materials have been used for packaging.
Corrugated board/cardboard (mainly from waste paper).
- shaped parts in PS (foamed CFC- free polystyrene)
- foils and bags in PE (polyethylene)
- strapping tapes in PP (polypropylene)
- Please hand over all packaging to the nearest official
collection point, so that all the different materials can
be re-used or recycled as far as possible and any
illegal depositing of such materials is thus avoided
2 Deciding where to locate your appliance
In order to avoid any damage or injury to persons or
things, the appliance should be unpacked by two people
and placed in the chosen location
Before positioning it, check that your new appliance
has no visible outer damage.
On no account should you start up your appliance if it is
damaged.
Check the appliance carefully for:
Damage to the packaging which might indicate that
appliance
has
transportation
Damage to the outer casing
Any visible damage to the cable / plug
If in any doubt
let the customer
check the appliance.
It must at all costs be avoided, that any environmentally
damaging
refrigerant
leaks
appliance.
3 Installing your appliance
a)
Unpack the fridge / freezer.
b)
In order not to unnecessarily waste
handles (requiring
smaller packaging)
mounted onto the separate parts of
the
door
handles
and
enclosed
parts
according
instructions enclosed separately.
c)
Remove any objects from inside the appliance
d)
Carefully remove all film and adhesive tape from the casing
from the door
e)
Remove any
polystyrene
compressor (if present).
f)
Remove all documents and accessories from inside the
appliance.
g)
Clean
the
inside
lukewarm water and vinegar and dry it thoroughly with
a soft cloth.
in the details
been
mishandled
during
service department
out
by
starting up the
raw materials, the
have not been
the appliance.Mount
at the same
time
anyother
to
the
relevant
pieces from
around the
of
the
appliance
with
Instruction for use
Do
not
use
washing
household products
or any other cleaning
containing soda.
Make sure that the pipes for the circulation of the
refrigerant
are
not damaged
installation of the appliance.
The appliance must only be used for the purpose for
which it is intended.
The appliance. must be
surface.
This is the only way to
refrigerant can circulate freely and thus ensure that
your appliance will work effciently.
If possible, place your appliance in a cool, well
aired, dry room.
Do not place your appliance in direct sunlight, nor in a
room at high temperature.
Do not place your appliance in
sources of direct heat such as heating, ovens, cooking
stove etc. (This would mean the compressor would
have
to work
harder and
consumption would be considerably higher).
If installation
near
a direct
avoided, we recommend fitting a suitable insulation plate
between the appliance and the heat source (do not use
asbestos), or at least the following minimum distances
must be observed:
.
from a gas or electric cooker
from a radiator or oven etc
from another refrigerating appliance
Do not place any appliances, such as microwaves,
toasters etc. which give off heat on the appliance
Never obstruct the ventilation grille.
Always pull out the plug itself and never pull the cable
when cutting the appliance off from the mains supply.
WARNING !
Leave the appliance standing in its final position for
at least 2 hours before switching it on, so that the
circulation
of
the refrigerant
operating problems occur.
Before connecting up the appliance, make sure that it
is absolutely dry inside - especially in the corners..
Danger warnings
Depending on its composition, the
easily inflammable.
The
hermetically sealed and has been tested many times for
possible leaks.
Any inexpert interference might well create a fire hazard.
Make sure nothing mechanically effects the circulation of
the refrigerant, nor, in particular, the accessible parts
around the compressor..
Only expert professional personnel should intervene
on the refrigerating system.
2
Refridgerator
liquids,
sharp
or
abrasive
agents
in
any
way during
placed on a firm, level
ensure that the
the vicinity of any
as a result
the power
heat
source cannot
30cm
30 cm
30 cm
stabilises
and no
refrigerant can be
refrigerant circuit
has
been
be
Publicidad
Capítulos
Tabla de contenido
