General Maintenance - Ryobi CP-180M Manual De Utilización

GB GB
F F D D
OPERATION
To switch from PSI, KG/CM
n With gauge ON, press and hold down ON/RESET
button for at least 7 seconds.
n The current measuring unit will flash. Press the
ON/RESET button again to select the desired
measuring unit.
n The setting takes effect after the display stops
flashing. (4-7 seconds)
NOTE: After preset pressure has been set, pressure
setting stays in the gauge memory. To recall the previous
pressure setting for up to 120 seconds after inflation,
press the ( + ) or ( - ) button.
To reset preset pressure, press and hold the ON/RESET
button.
INFLATING MANUALLY FOR HIGH AND LOW PRESSURE
APPLICATIONS
n Connect either high or low pressure hose to item to be
inflated.
n Depress and hold switch trigger until desired pressure
is reached.
n Release the switch trigger.
INFLATING USING THE PRESET PRESSURES FEATURE
WITH AUTOMATIC SHUTOFF
NOTE: Digital gauge displays pressure of high pressure
hose only.
n With gauge ON, press and hold down ( + ) or ( - )
buttons to select desired shutoff pressure.
NOTE: Numbers will flash while setting pressure.
Holding buttons down will make the pressure number
increase/decrease faster.
n Depress switch trigger.
n Push the lock-on button forward.
n Release the switch trigger and the inflator will continue
running.
NOTE: For preset pressures of 39 PSI, 2.65 BAR or
2.80 KG/CM² or less, the unit will automatically stop just
short of the preset pressure. Manually depress the switch
trigger again to release the lock-on button and provide an
additional short "burst" of air to achieve preset pressure.
For preset pressures of 40 PSI, 2.75 BAR or 2.80 KG/
CM² or greater, the unit will automatically stop at 40 PSI,
2.75 BAR or 2.80 KG/CM² regardless of preset pressure
setting. This feature helps guard against over inflation and
possible bursting. Manually depress the switch trigger
again to release the lock-on button and continue inflating
by holding the trigger in the ON position to achieve
E E I I P P NL NL
2
and BAR:
S S DK DK N N FIN FIN GR GR
English English
desired pressure. Shutoff will occur again just before
target pressure is reached.
NOTE: Read actual pressure only when unit is not
operating.
MAINTENANCE

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
Only the parts shown on the parts list are intended to
be repaired or replaced by the customer. All other parts
should be replaced at an Authorized Service Center.
REPLACEMENT FUSE (FIG. 12)
A fuse has been supplied with the inflator to replace the
inflator fuse when needed.
n Remove the current fuse and discard.
n The replacement fuse supplied with the inflator is
located on the inside cover of the high pressure air
hose. Use this fuse install to replace the blown fuse.
NOTE: Use only 20 amp JAT blade automotive fuses for
replacement.
12
RO RO
H H CZ CZ RUS RUS
WARNING:
When servicing, use only identical replacement
parts. Use of any other parts may create a
hazard or cause product damage.
WARNING:
Always wear safety goggles or safety glasses
with side shields during power tool operation or
when blowing dust. If operation is dusty, also
wear a dust mask.
WARNING:
To avoid serious personal injury, always remove
thebattery pack from the tool when cleaning or
performing any maintenance.
WARNING:
Do not at any time let brake fluids, gasoline,
petroleum-based products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can
damage, weaken ordestroy plastic which may
result in serious personal injury.
HR HR
PL PL SLO SLO TR TR