Tabla de contenido
Publicidad
ATTACH TO JUNCTION BOX
CC x1
2N1
2N1
The fixture is not a dusk-to-dawn light. The fixture has a built-in dusk-to-dawn sensor that prevents the motion sensor from activating during daylight hours.
SECURITY LIGHT
SECURITY LIGHT
(High Beam)
(High Beam)
AREA LIGHT MODE SETTINGS
Range
30
60
1
Test
5
Max.
Feet
Minutes
2N1
TEST MODE SETTINGS
Range
30
60
1
SECURITY LIGHT
(High Beam)
Test
5
Max.
Feet
Minutes
When the MINUTES control is set to TEST, the light will operate both
during daylight and night time.
Allow the motion sensor about 2 minutes to warm up prior to
conducting the "walk by test".
SECURITY LIGHT MODE SETTINGS
Range
30
60
1
Test
5
Max.
Feet
Minutes
The MINUTES control determines the length of time the lights stay on.
When the MINUTES control is set between 1 and 10, the light will only
come on during night time hours.
Range
60
30
1
5
Max.
Test
Feet
Minutes
DO NOT POSITION THE SENSOR WITH THE CONTROLS FACING UPWARD.
The position of the sensor should not exceed 45° below horizontal. Do not aim
the motion sensor at any water, bushes or plants that may move in the wind,
pedestrian traffic, moving cars, etc., as this may trigger the motion sensor.
(Fig. 2)
NOTE: If the sensor arm becomes loose, readjust the sensor head and
tighten the joint screw on the sensor arm.
Silicone
EE x1
AREA LIGHT
AREA LIGHT
(Low Beam)
(Low Beam)
(Low Beam)
Turn the AREA LIGHT MODE control knob to either 3 hrs, 5hrs or Dusk-to-Dawn. The 3 hrs setting turns
the Area Light on at dusk for a duration of 3 hours. The 5 hrs setting turns the Area Light on at dusk for a
duration of 5 hours. The Dusk-to-Dawn setting turns the Area Light on at dusk for the duration of the
3hrs
5hrs
5
night until it shuts off at dawn. The OFF setting disables the area light feature completely, and fixture
operates strictly as a security light triggered by the motion sensor (PIR).
SET RANGE KNOB TO
10
OFF
Dusk To Dawn
Any distance (5 - Max.(100 ft.))
TEST MODE:
3hrs
5hrs
5
AREA LIGHT
Rotate the MINUTES control knob to TEST to calibrate the fixture. Both lights will turn on for
approximately 20 seconds.
(Low Beam)
With the control knob still on TEST, do a "walk by test" by walking in front of the motion sensor (as
10
indicated in Fig. 1 below). As movement is detected, the lights will activate. Stop and the lights shut
OFF
Dusk To Dawn
off approximately 5 seconds after movement is no longer detected in the sensor's field. Continue
walking and the lights should once again turn on. Once out of the detection range, the lights will shut
off and the test is complete. IF THE TEST FAILS, try readjusting the sensor head. Sensor head can be
adjusted either up or down, or left or right. Once fixture is tested, set middle control knob to desired
time the light stays on once motion is detected.
SET RANGE KNOB TO
Any distance (5 - Max.(100 ft.))
(High Beam)
SETTING THE LIGHT ACTIVATION TIME:
3hrs
5hrs
5
Rotate the MINUTES control knob clockwise past the TEST area to control the length of time the lights
will remain on. The time settings of 1 (1 min.), 5 (5 min.) and 10 (10 min.) are marked. However, the
MINUTES control knob can be set anywhere from 1 minute up to 10 minutes. The time length can be
adjusted up or down. DO NOT rotate the MINUTES control knob back to the TEST area.
10
OFF
Dusk To Dawn
SET RANGE KNOB TO
Any distance (5 - Max.(100 ft.))
SETTING THE MOTION DETECTION RANGE:
Rotate the RANGE control knob anywhere from 5 Ft to MAX. (100 ft).
3hrs
5hrs
5
When the RANGE control knob is turned to 5 Ft, the detection zone is
very tight and compact, causing the detection sensitivity to be very
high. The reverse is true, when the RANGE control knob is turned to
10
MAX, the detection zone increases exponentially with sensitivity being
OFF
Dusk To Dawn
low. Perform a "walk by test" by walking across the motion detection
field at the approximate distance set on the RANGE control knob (Fig. 1) .
IF THE TEST FAILS, try adjusting the sensor head toward the detection zone.
45°
MAX.
SET RANGE KNOB TO
Any distance (5 - Max. (100 Ft.))
Align the center holes of the fixture and mounting strap (attached to the
J-box). Insert the long machine screw (CC) through the fixture's center hole
and drive into the strap. Restore power to the electrical box and verify the
light functions properly.
For round surface mount junction boxes make sure the gasket (GG) properly seals the gap
between the wall plate and electrical box to prevent water from seeping into the j-box.
For recessed mount junction boxes, use silicone adhesive caulking (not included) to seal the gap
between the wall plate and the mounting surface to prevent water seepage into the j-box.
If the light is functioning properly, install the silicone cap (EE) into the center
hole on the fixture base to prevent water from entering the housing.
SET MINUTES KNOB TO
SET MINUTES KNOB TO
SET MINUTES KNOB TO
to MAX.
Sensor head can be adjusted either up or down, or left or right.
MOTION SENSOR
The 240-degree coverage of the motion sensor is measured side-to-side.
The sensor is more effective side-to-side, rather than motion coming
straight at it (in-and-out). Adjust the motion sensor head so that it detects
motion moving across the coverage area.
Fig. 2
SET MINUTES KNOB TO
SET WALL SWITCH TO
Any time (1-10).
SET WALL SWITCH TO
TEST
SET WALL SWITCH TO
Any time (1-10).
SET WALL SWITCH TO
Any time (1-10).
ON
ON
ON
240°
Fig. 1
ON
2
Publicidad
Tabla de contenido
