Tabla de contenido
Publicidad
USING MANUAL OVERRIDE
ON
ON
OFF
OFF
2 Seconds
MANUAL OVERRIDE allows the light to turn on at any time, by overriding all sensor
controls, so the light comes on regardless of time of day.
Troubleshooting Guide
PROBLEM
Security light
1. Light switch is off.
does not come on
2. Fuse is blown/circuit breaker has tripped.
3. Fixture not properly wired to junction box.
4. It is daylight.
5. Motion sensor is pointed in the wrong direction.
6. Air temperature is about the same as a person's body
temperature and the (PIR) sensor cannot "see" the person.
Light continuously
1. Light sensor is triggered by reflected light from
cycles ON and OFF
the security light itself.
(strobe effect).
2. Heat is being reflected from other sources and may be
triggering sensor on and off.
Light turns on during
1. Light may be installed in shadows/dark area.
daylight hours.
2. The MINUTES control knob is set to TEST.
Light comes on for
1. Sensor may be triggered by a small animal or passing car.
no apparent reason.
2. Hot air (dryer vent, car exhaust, etc.) may be triggering
the sensor.
Light stays on
1. Motion sensor may be picking up a continuos flow of warm
continuously.
air from an air vent, dryer vent or heat reflecting off a surface.
2. Interference generated from transformers, fluorescent light
fixtures or electric motors are connected to the same circuit.
1. The MINUTES control knob is set to TEST.
Light flashes on for
20 seconds at a time
day or night.
REPLACEMENT PARTS LIST
FCC STATEMENT:
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on
a circuit different from that of the receiver. 4) Consult the dealer or an experienced radio/TV technician for help.
Good Earth Lighting
- 10 YEAR LIMITED WARRANTY:
®
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of (10) years from the date of original purchase by the
consumer. The fixture is not warrantied for use in a commercial or retail application. The warranty is limited to use in a residential environment. We will repair or replace (at our
option) the unit in the original color and style if available, or in a similar color and style if the original item has been discontinued, without charge. Defective units must be
properly packed and returned to the manufacturer with a letter of explanation and your original purchase receipt showing date of purchase. Call 1-800-291-8838 to obtain a
return authorization number and an address where to ship your defective product. Note: C.O.D. shipments will NOT be accepted. The liability of the manufacturer is in any case
limited to replacement of the defective light fixture product. The manufacturer will not be liable for any other loss, damage, labor costs or injury which is caused by the product.
This limitation upon the liability of the manufacturer includes any loss, damage, labor costs or injury which is (I) to person or property or otherwise; (II) incidental or
consequential in nature; (III) based upon theories of warranty, contract, negligence, strict liability, tort, or otherwise; or (IV) directly, or indirectly related to the sale, use, or
repair of the product. This warranty gives you specific rights, and you may also have other rights which vary from state to state.
Need Help?
Please visit our website at: www.goodearthlighting.com/support or call the Customer Care Center
1-800-291-8838, 8:30 a.m.-5 p.m., CST, Monday-Friday.
Good Earth Lighting® 1400 East Business Center Drive, Ste. 108 Mount Prospect, IL 60056
Printed in China
SETTING THE LIGHT MANUAL OVERRIDE:
If the security light has been turned off at the switch, turn it on for 60 seconds to allow the (PIR) sensor
ON
ON
time to warm up prior to initiating the manual override sequence.
To switch over to manual mode, switch the power OFF-ON-OFF-ON within 2 seconds. There are 2 ways to
return to sensor control:
OFF
OFF
1) To immediately switch out of manual mode, repeat the manual mode sequence of power
OFF-ON-OFF-ON within 2 seconds. This will cancel out manual mode.
2) The security light will remain on until the internal dusk-to-dawn sensor detects the next dusk-dawn
cycle. Once light is detected, it will allow the motion sensor to return to controlling the fixture the next day.
POSSIBLE CAUSE
CORRECTIVE ACTION
1. Turn light switch on.
2. Replace fuse/ turn the circuit breaker back on.
3. Re-install light fixture.
4. Recheck at night.
5. Readjust motion sensor.
6. Decrease the RANGE control setting.
1. Change the position of the light head, aim light away from the reflecting
surfaces.
2. Decrease the RANGE control setting.
1. Light is operating as it was designed. Use manual override if necessary.
2. Set the MINUTES control knob somewhere between 1 and 10.
1. Decrease the RANGE control setting as necessary.
2. Increase the RANGE control setting as necessary.
1. Reposition the motion sensor.
2. Install the light on a circuit without transformers, fluorescent light
fixtures or electric motors connected to the circuit.
1. Set the MINUTES control knob somewhere between 1 and 10.
Hardware Kit:
ZH-SE1095F02
3
Publicidad
Tabla de contenido
