Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
AX-ADXSVI-AU2
Audi CAN interface 2002-2007
Note: This harness must be used in conjunction with the AX-ADXSVI.
• Provides accessory (12-volt 10-amp)
• Retains R.A.P. (retained accessory power)
• Provides NAV outputs (parking brake, reverse, and speed sense)
• Prewired ASWC-1 harness (ASWC-1 sold separately)
• Retains balance and fade
• Micro "B" USB updatable
APPLICATIONS
AUDI
A3*
2006-2007
A6
2004
A4/S4**
2002-2006
INTERFACE COMPONENTS
• XSVI-AU2 harness
TOOLS REQUIRED
• Cutting tool • Tape • Crimping tool
• Connectors (i.e. butt-connectors, bell caps, etc.)
METRA. The World's best kits.™
Installation Instructions for AX-ADXSVI-AU2
FEATURES
allroad
2004-2005
TT
2002-2006
Note: *With concert radio (without NAV)
**With symphony radio (without NAV)
1-800-221-0932
Caution: Metra recommends disconnecting the negative battery terminal before
beginning any installation. All accessories, switches, and especially air bag indicator
lights must be plugged in before reconnecting the battery or cycling the ignition.
*Note: Refer also to the instructions included with the aftermarket radio.
Connections to be made
From the XSVI-AU2 harness to the aftermarket radio
(a) From the 12-pin harness:
• Connect the Red wire to the accessory wire.
• Connect the Orange wire to the illumination wire, if the aftermarket radio has
no illumination wire, tape off the Orange wire.
The following wires are for aftermarket multimedia/navigation radios that provide
these wires (if not required, tape them off and disregard them):
• Connect the Light Green wire to the parking brake wire, if applicable.
• Connect the Green/Purple wire to the reverse wire, if applicable.
• Connect the Blue/Pink wire to the speed sense (V.S.S.) wire, if applicable.
(b) From the 16-pin harness:
• Connect the Black wire to the ground wire.
• Connect the Yellow wire to the battery wire.
For non-BOSE systems:
• Connect the White wire to the left front positive speaker output.
• Connect the White/Black wire to the left front negative speaker output.
• Connect the Gray wire to the right front positive speaker output.
• Connect the Gray/Black wire to the right front negative speaker output.
Tape off and disregard the following wires, they will not be used in this application:
• The Green, Green/Black, Purple, Purple/Black wire.
metraonline.com
(continued on next page)
© COPYRIGHT 2004-2014 METRA ELECTRONICS CORPORATION
Publicidad
Manuales relacionados para Audi AX-ADXSVI-AU2
Resumen de contenidos para Audi AX-ADXSVI-AU2
- Página 1 Installation Instructions for AX-ADXSVI-AU2 Caution: Metra recommends disconnecting the negative battery terminal before AX-ADXSVI-AU2 beginning any installation. All accessories, switches, and especially air bag indicator lights must be plugged in before reconnecting the battery or cycling the ignition. Audi CAN interface 2002-2007 *Note: Refer also to the instructions included with the aftermarket radio.
- Página 2 AX-ADXSVI-AU2 For BOSE systems: Tape off and disregard the following wires, they will not be used in this application: Installing the AX-ADXSVI-AU2 • The Green, Green/Black, Purple, Purple/Black, White, White/Black, Gray, • Connect the 12-pin harness into the AX-ADXSVI (sold separately). and Gray/Black wire. • Connect the 16-pin harness into the vehicle. • Connect the 26-pin harness into the vehicle. From the 26-pin harness: • With all connections completed, reconnect the negative battery terminal. • Connect the Blue/White wire to the amp turn on wire (this wire must be • Initialize the interface by turning the ignition on for 30 seconds, then turn the connected to hear sound from the factory amplifier). ignition back off, then back on again. For non-BOSE systems: Note: If using the ASWC-1, connect it after you initialize the AD-ADXSVI-AU2, • Disregard the White RCA, it will not be used in this application.
- Página 3 Instrucciones de instalación para AX-ADXSVI-AU2 Precaución: Metra recomienda desconectar el terminal negativo de la batería antes de AX-ADXSVI-AU2 comenzar cualquier instalación. Todos los accesorios, interruptores y, especialmente, las luces indicadoras de airbag deben estar enchufados antes de volver a conectar la Audi CAN interfase 2002-2007 batería o comenzar el ciclo de ignición.
- Página 4 AX-ADXSVI-AU2 Para sistemas BOSE: Encinte e ignore los siguientes cables, no se utilizarán en esta aplicación: • El cable verde, verde/negro, púrpura, púrpura/negro, blanco, blanco/ Instalación del AX-ADXSVI-AU2 negro, gris y gris/negro. • Conecte el arnés de 12 pins al AX-ADXSVI (se vende por separado). • Conecte el arnés de 16 pins al vehículo. Desde el arnés de 26 pins: • Conecte el arnés de 26 pins al vehículo. • Conecte el cable azul/blanco al cable de encendido del amplificador (este • Cuando todas las conexiones estén hechas, vuelva a conectar la terminal cable debe estar conectado para escuchar sonido del amplificador de fábrica). negativa de la batería. • Para inicializar la interfase, encienda la marcha y espere 30 segundos, luego Para sistemas distintos a BOSE: vuelva a apagar la ignición, y enciéndala una vez más. • Ignore el conector RCA blanco, no se utilizará en esta aplicación. Nota: Si va a utilizar el ASWC-1, conéctelo después de inicializar el • Ignore el conector RCA gris, no se utilizará en esta aplicación.