Publicidad
Idiomas disponibles
Idiomas disponibles
"Metric
"Entry Thread
"Entry
NPT Catalog
"Over Conductors
(Metric
Catalog
Thread"
No
O.D. Max Inches"
No."
Option)"
1-1/4"
TMCX125 2
M40
TMCXM40 2
1-1/2"
TMCX150 1
M50
TMCXM50 1
1-1/2"
TMCX150 2
M50
TMCXM50 2
2"
TMCX200 1
M63
TMCXM63 1
2"
TMCX200 2
M63
TMCXM63 2
2-1/2"
TMCX250 1
M75
TMCXM75 1
2-1/2"
TMCX250 2
M75
TMCXM75 2
3"
TMCX300 1
M90
TMCXM90 1
3"
TMCX300 2
M90
TMCXM90 2
3-1/2"
TMCX350 1
M110
TMCXM110 1
3-1/2"
TMCX350 2
M110
TMCXM110 2
4"
TMCX400 1
4"
TMCX400 2
SELECTION TABLE CONTINUED
MCHL
MC – Class I, Div 2; Class II, Div. 2; Class III
NPT
Class I, Class II, Class III
TECK – cUL Class I, Div. 1
Catalog No.
Min.
Max.
Min.
TMCX125 2
1.03
1.65
1.03
TMCX150 1
1.03
1.65
1.03
TMCX150 2
1.42
2.07
1.42
TMCX200 1
1.42
2.07
1.42
TMCX200 2
1.81
2.77
1.78
TMCX250 1
1.81
2.77
1.78
TMCX250 2
2.24
3.28
2.24
TMCX300 1
2.24
3.28
2.24
TMCX300 2
2.66
3.68
2.65
TMCX350 1
2.66
3.68
2.65
TMCX350 2
3.1
3.97
3.13
TMCX400 1
2.66
3.68
2.65
TMCX400 2
3.1
3.97
3.13
*For TMCX II assemblies with 1.25" NPT or smaller thread bodies, please refer to Instruction Sheet IF 1647.
*All dimensions in inches; metric millimeters shown in parenthesis.
†When making your cable gland selection based on Cable O.D., be sure to also observe the Over Conductors O.D. dimension.
See pages 7 and 8 for gel time graphs.
IF 1647B • 08/15
Copyright © 2015, Eaton's Crouse-Hinds Division
SELECTION TABLE
Armour O.D.
"Empty Sealing Chamber Volume
Min.
Max.
(Assuming no conductors present)"
1.15
0.94
1.67
1.37
0.94
1.67
1.37
1.28
1.97
1.76
1.28
1.97
1.76
1.67
2.62
2.14
1.67
2.62
2.14
2.11
2.95
2.69
2.11
2.95
2.69
2.45
3.39
3.13
2.45
3.39
3.57
3.05
4.22
3.13
2.45
3.39
3.57
3.05
4.22
MC/TECK
Tray
Class I, Div. 2; Class II, Div 2;
Class III
Max.
Min.
1.72
1.03
1.72
1.03
2.07
1.53
2.07
1.53
2.72
2.72
3.13
3.13
3.61
3.61
3.61
NEMA 4 RATED CABLE RANGES**
NPT CATALOG NO.
[mL]
TMCX125 2
TMCX150 1
37
TMCX150 2
53
TMCX200 1
53
TMCX200 2
86
TMCX250 1
86
TMCX250 2
128
TMCX300 1
128
TMCX300 2
202
TMCX3501
202
TMCX350 2
273
TMCX400 1
355
TMCX400 2
273
355
**NEMA rating applies to assemblies using the noted cable size
ranges only.
ADDITIONAL INSTALLATION
CONSIDERATION
If the back nut of the rear assembly becomes dislodged during
handling, make sure to rebuild the assembly in its original
Max.
configuration.
1.71
1.
First ensure that the grounding spring is still captive to the
1.71
assembly by one of the plastic retaining rings.
2.
To reassemble the gland, you will have to remove the
2.07
retaining ring holding the grounding spring. This can be
accomplished with a tool like a thin screwdriver. Make
2.07
sure the grounding spring is not damaged while removing
the retaining ring and set it somewhere safe where it will
not get damaged or exposed to a corrosive environment
when it has become loose from the assembly.
3.
Next, remove the second retaining ring from the back nut
in a similar manner; ensuring the rubber environmental
seal does not get soiled, and that the Teflon washer is not
torn or damaged.
4.
Install the two (2) retaining rings over the outer lips of
the rubber environmental seal, making sure they have
snapped in 360°.
5.
Install the retaining ring and environmental seal into the
back nut. You should feel or hear a snap, and ensure it is
snapped in 360°.
6.
Fasten the back nut back onto the rear assembly for at
least 1/4" .
All statements, technical information and recommendations contained herein are based on information and tests we believe to be
reliable. The accuracy or completeness thereof are not guaranteed. In accordance with Eaton's Crouse-Hinds Division's "Terms and
Conditions of Sale," and since conditions of use are outside our control, the purchaser should determine the suitability of the product
for his intended use and assumes all risk and liability whatsoever in connection therewith.
Page 3
MIN.
MAX.
1.03
1.71
1.03
1.71
1.50
2.07
1.50
2.07
1.81
2.72
1.81
2.72
2.34
3.28
2.34
3.28
2.68
3.78
2.68
3.78
3.13
4.28
2.68
3.78
3.13
4.28
Eaton's Crouse-Hinds Division
1201 Wolf Street Syracuse, New York 13208 • USA
Copyright © 2015
IF 1647B
Revision 2
Revised 08/15
Supercedes 09/14
Publicidad
