General Instructions - SPORT-ELEC BODY BEAUTIFUL Manual De Instrucciones

B / UsIng ThE UnIT
step 1 - on / oFF " "
• A short press on the " " key puts the device under or except power.
• Every time when the power is on, the device carries out an auto-test on 11 essential safety parameters.
During the auto-test all the indicators are lit during ½ second.
• If an internal defect in the device is detected, all the pictograms flash in green and the device stops.
Then, return the device to After Sales Service.
• The auto-test does not take into account the detection of the used batteries.
When batteries are used, the auto-test is not activated.
• A long press (of more than 3 seconds) involves the release of the auto-test.
In this case stop the device, please, by pressing the key " " and then make a short press on the key " ".
step 2 - prograM selection keY " "
To select a program, make one or more short presses on the key "
The programs are announced by pictograms.
As soon as a program is selected, corresponding pictogram lights.
Once the program is chosen, you can start it by increasing the power on one of power keys " ".
During the program the key " " is inactive.
step 3 - end oF the prograM - stop during the prograM
At the end of the session the device stops automatically.
To stop the device during the program, put the 2 power keys back on zero or press the key " ".
step 4 - adjustMent oF the power
The power is divided into 10 levels: 5 green, 3 orange and 2 red levels.
To change the level press the key " ".
You have 72 levels to regulate the power from 0 to 72.
step 5 - Batteries
• If the batteries are "good", there is no blinking.
• If the batteries are "weak", two orange indicators blink. Your device still functions.
• If the batteries are "used", two red indicators blink. Your device stops, even in the course of a program. Change the batteries.
step 6 - disconnection
Your device is equipped with a detector of electrodes disconnection.
If the contact between the human body and a single electrode is absent, the power is stopped on the concerned channel
(channel A = orange / channel B = green).
You are warned of a disconnection by blinking of green indicator during 30 seconds, after 30 seconds the blinking stops.
If none of the electrodes is in contact with the body, the power cannot be emitted.
III. gEnErAL InsTrUcTIOns
A. UsIng ThE DEVIcE WITh ThE ELEcTrODEs
This function allows you to use the adhesive electrodes by connecting them directly to the modules.
You can use the device with 1 or 2 modules.
getting started
Connect each module to the unit by matching the color indicators (photo A page 4)
f f
Fix the electrodes to the module(s) using the snap fasteners (photo B page 4)
positioning oF the electrodes
Remove the plastic backing sheet from the electrodes (photos C page 4).
f f
Moisten them by spreading a few drops of water onto the adhesive gel using your fingertips and wait 2 minutes.
Position the electrode(s) onto your body.
f f
NB: The electrodes are for personal use. For hygiene reasons, they must always be used by the same person.
starting the prograM:
14
", the programs scroll.
Start your device by following the «Starting the device» procedure.
Contractions should be firm but must never cause any pain.
If the electrodes cause you any discomfort: reduce the power levels, move the electrode(s) and then gradually increase the
power. Also ensure that the electrodes are sufficiently moistened.
Now that the settings have been optimized, let your device get to work for the full duration of the program.
end oF prograM:
Once the program has finished, switch off the device by pressing the
Gently remove the electrodes from your skin.
Moisten them slightly with a few drops of water and replace them carefully onto their transparent plastic backing sheet.
Keep the adhesive electrodes in a plastic bag in a cool place (for example, a separate compartment in your refrigerator).
B. UsIng ThE DEVIcE WITh ThE BELT
The belt has 2 pairs of snap fasteners onto which 2 wireless electrodes specially designed by SPORT-ELEC® are clipped.
To obtain new electrodes, contact your usual retailer or order them from our website www.sport-elec.com.
warning!
Never use the belt without attaching the 2 electrodes provided.
Only use electrodes supplied by SPORT-ELEC®.
presentation oF the Belt:
1
= Snap fasteners
2
= Wire storage flap
(with a lopp fixing device)
3
= Partie auto-agrippante
connection and positioning oF the Belt.
Check that your device is switched off.
f f
Open out the belt.
f f
Fix the electrodes to the inside of the belt using the snap fasteners.
f f
Place the belt around the waist and adjust it using the Velcro strip, so that there is a good contact between the electrodes and the
f f
skin. If required, use the belt extension.
Once the belt is in position, fix 2 modules onto the snap fasteners.
f f
If you experience any tingling, switch off the device and check that the electrode is in contact with the skin. If the problem persists,
f f
contact the after-sales service: sav@sport-elec.com.
starting the prograM with the Belt
Once your device is connected, make yourself comfortable and switch it on following the «Starting the device» procedure.
You can carry out your normal activities while using the device.
end oF prograM
Once the program has finished, switch off the device and unplug it from the belt.
Remove the electrodes and moisten them slightly with a few drops of water before replacing them onto their transparent plastic
backing sheets.
IV. prEcAUTIOns
Hypersensitivity to electro-stimulation may cause a skin reaction in certain individuals.
f f
Keep out of the reach of children or mentally-impaired persons. This product contains small parts which can be easily swallowed.
f f
Only use Body Beautiful with the accessories supplied and recommended by SPORT-ELEC® INSTITUT.
f f
Do not use Body Beautiful when driving, operating machinery, or during any activity where electro-stimulation could result in the
f f
risk of injury to the user.
Always position the belt in accordance with the information provided in this manual.
f f
button, then disconnect the modules.
1
2
3
1
15