Installation Instructions - Beko HBG70X Manual De Utilización

applicable for external air evacuation.
Before connecting the model to the electricity network:
- Control the data plate (positioned inside the appliance)
to ascertain that the voltage and power correspond to the
network and the socket is suitable. If in doubt ask a qualified
electrician.
- If the power supply cable is damaged, it must be replaced
with another cable or a special assembly, which may be
obtained direct from the manufacturer or from the technical
Assistance Centre.
- this device must be connected to the mains supply through
either a plug fused 3A or hardwired to a 2 phase spur pro-
tected by 3A fuse.
2. Warning!
In certain circumstances electrical appliances may be a
danger hazard.
A) Do not check the status of the filters while the cooker
hood is operating.
B) Do not touch bulbs or adjacent areas, during or straight
after prolonged use of the lighting installation.
C) Flambè cooking is prohibited underneath the cooker
hood.
D) Avoid free flame, as it is damaging for the filters and
a fire hazard.
E) Constantly check food frying to avoid that the
overheated oil may become a fire hazard.
F) Disconnec t the elec trical plug prior to any
maintenance.
G) This appliance is not intended for use by young children
or infirm persons without supervision.
H) Young children should be supervised to ensure they do
not play with the appliance.
I) There shall be adequate ventilation of the room when the
rangehood is used at the same time as appliances burning
gas or other fuels.
L) There is a risk of fire if cleaning is not carried out in
accordance with the instructions.
this appliance conforms to the European Directive EC/2002/96,
Waste Electrical and Electronic Equipment (WEEE). By making
sure that this appliance is disposed of in a suitable manner,
the user is helping to prevent potential damage to the
environment or to public health.
the symbol on the product or on the accompanying
paperwork indicates that the appliance should not be treated
as domestic waste, but should be delivered to a suitable
electric and electronic appliance recycling collection point.
Follow local guidelines when disposing of waste. For more
information on the treatment, re-use and recycling of this
product, please contact your local authority, domestic waste
collection service or the shop where the appliance was
purchased.

INSTALLATION INSTRUCTIONS

• Assembly and electrical connections must be carried out
by specialised personnel.
• Wear protective gloves before proceeding with the
installation.
• Electric Connection
Note: Verify the data label placed inside the appliance:
- If the symbol appears on the plate, it means that no earth
connection must be made on the appliance, therefore follow
the instructions concerning insulation class II.
- If the symbol DOES NOt appear on the plate, follow the
instructions concerning insulation class I.
Insulation class II
the appliance has been manufactured as a class II, therefore
no earth cable is necessary.
the plug must be easily accessible after the installation of
the appliance. If the appliance is equipped with power cord
without plug, a suitably dimensioned omnipolar switch
with 3 mm minimum opening between contacts must be
fitted between the appliance and the electricity supply in
compliance with the load and current regulations.
the connection to the mains is carried out as follows:
BROWN = L live wire
BLUE = N neutral
Insulation class I
this is a class I, appliance and must therefore be connected
to an effiecient earthing system.
the appliance must be connected to the electricity supply
as follows:
BROWN = L live wire
BLUE = N neutral
YELLOW/GREEN =
the neutral wire must be connected to the terminal with the
N symbol while the YELLOW/GREEN, wire must be connected
to the terminal by the earth symbol
Warning:
When connecting the appliance to the electricity supply, make
sure that the mains socket has an earth connection. After fitting
the ducted cooker hood, make sure that the electrical plug is
in a position where it can be accessed easily. If the appliance
is connected directly to the electricity supply, an omnipolar
switch with a minimum contact opening of 3 mm must be
placed in between the two; its size must be suitable for the load
required and it must comply with current legislation.
• the minimum distance between the support surfaces of
the cooking pots on the cooker top and the lowest part of
the cooker hood must be at least 65 cm. If a connection tube
composed of two parts is used, the upper part must be placed
outside the lower part. Do not connect the cooker hood
exhaust to the same conductor used to circulate hot air or for
evacuating fumes from other appliances generated by other
than an electrical source.
Before proceeding with the assembly operations, remove the
anti-grease filter(s) (Fig.7) so that the unit is easier to handle.
In the case of assembly of the appliance in the suction version
prepare the hole for evacuation of the air.
• We recommend the use of an air exhaust pipe with a
diameter of 150. If a pipe with a smaller diameter is used, the
efficiency of the product may be reduced and its operation
may become noisier.
Please note:
If your version of the appliance has decorative glass before
installing the hood, carry out the following steps as shown
in figure 4:
1 - Remove both the cooker hood body B and the glass
panel A from the packaging and place them horizontally on
a secure surface.
2 - take the glass panel A and position it above the cooker
hood body B.
3 - Fix the glass panel securely to the cooker hood body using
- 16 -
earth
.