Changing The Saw Blade; Technical Data; Saw Dimensions - Urrea SM1010 Manual De Usuario Y Garantía

bricate rack and gears with a medium viscosity
machine oil.
• Be sure to lubricate trunnion ways and all
bushings.
• Occasionally oil all other bearing points, in-
cluding blade guard assembly, miter gauge
and rip fence.
SERVICE
• Replace belts and worn parts as needed. If
power cords are worn, cut, or damaged in any
way, have them replaced immediately.
• Make sure teeth of anti-kickback pawls are
always sharp.
• Sharpen dull teeth using a few light strokes
of a smooth cut flat file.

CHANGING THE SAW BLADE

WARNING: Turn the power switch "OFF"
and unplug the power cord from its power
source when changing the saw blade.
WARNING: When replacing blades, check
the thickness stamped onto the riving knife.
You must select a blade with a kerf width larg-
er than the thickness of the riving knife. Thin-
ner blades may cause the workpiece to bind
during cutting.
WARNING: Use only 10" diameter blades
with 5⁄8" arbor holes, rated at or higher than
3800 R.P.M.
• Remove blade guard assembly and pawl as-
sembly.
• Remove the table insert.
• Unlock the raise/lower handwheel lock and
raise saw blade to maximum height.
• Depress locking pin and slowly rotate blade
toward you until pin engages into arbor. Hold
arbor in locked position.
Locking pin
• Place supplied open-end wrench (A) on the
arbor nut (B). Turn wrench counterclockwise to
loosen nut. Remove arbor nut, blade flange (C)
and saw blade (D)
52
A
D
• Place new blade on arbor. Make sure saw
blade teeth point down at the front side of
saw table. Place flange and nut on arbor and
securely snug blade in position.
• Replace table insert.
• Replace blade guard assembly and pawl as-
sembly.

TECHNICAL DATA

CAPACITY WITH 10"
...................... 3 1/8"
DEPTH OF CUT AT 90°
MAXIMUM TILT ANGLE OF ARBOR (LEFT)........................45°
........................................2 3/16"
DEPTH OF CUT 45°
MAX. CUT RIGHT OF BLADE WITH RIP FENCE
MAX. CUT LEFT OF BLADE WITH RIP FENCE....................13"

SAW DIMENSIONS:

..............................................37 3/8"
TABLE HEIGHT
CABINET DEPTH.....................
............................. ... 19 1/2"
CABINET WIDTH ..........
TABLE AREA...................................
FRONT OF TABLE TO BLADE ...................................
RIP FENCE DIMENSIONS:
RIP FENCE...............................................
RIP FENCE RAILS (FRONT AND REAR)
BLADE CAPACITY MAXIMUM ......
........................................... 5/8"
BLADE ARBOR ........
DADO BLADE CAPACITY MAXIMUM .................................13/16"
SAW CONSTRUCTION
CABINET ..................................TOTALLY ENCLOSED STEEL PANEL
TABLE.............................................................................CAST IRON
RIP FENCE .........................................................ALUMINIUM TUBE
DRIVE SYSTEM .....................................................................V-BELT
EXHAUST PORT..................................................................4" MALE
MITER GAUGE ............. CAST IRON WITH T-SLOT ROLLER GUIDE
BLADE GUARD .............. ACRYLIC WITH ANTI-KICKBACK PAWLS
SWITCH..................LOCKING PADDLE SWITCH WITH OVERLOAD
ARBOR R.P.M. ..................................................3450 RPM APPROX.
MOTOR........
1800W, 3550 RPM, CAPACITOR START,CAPACITOR RUN,
120/240V, 140 Kg, SINGLE- PHASE, BALL BEARING
GROSS WEIGHT WITH MOTOR..............................................308lb
B
C
.............30"
................................. 22"
26 5/16" X 20 3 /16"
11 3/4"
............. 31 1/4"
............... 56 1/2"
......................... 10"