Prior To Installation - Jøtul F 370 Serie Manual De Instalación Con Información Técnica

Wood consumption
Jøtul F 370 has a nominal heat output of 5,5 kW. Use of
wood, with nominal heat emission: Approx. 1,9 kg/h. Another
important factor for proper fuel consumption is that the
logs are the correct size. The size of the logs should be:
Kindling:
Length: 30 cm
Diameter: 2-5 cm
Amount per fire: 6-8 pieces
Firewood (split logs):
Length: Ca 20 - 30 cm
Diameter: Approx. 8 cm
Intervals for adding wood: Approximately every 45 minutes
Size of the fire: 1.4 kg
Amount per load: 2 pieces
Nominal heat emission is achieved when the air vent (fig. 26 A)
is open approximately 100% and the handle for the ignition vent
pulled out approximately 1-2 cm (fig. 26 B).
2.1 Floor
Foundations
It must be ensured that the foundations are dimensioned for
the fireplace. Cf. «2.0 Technical data» for specification of weight.
It is recommended that flooring which is not fastened to the
foundations – so-called floating flooring – is removed during
installation.
Combustible floor protection
Jøtul F 370 Series (except from Jøtul F 374) has a heat shield
underneath which protects the base from radiation. The product
has an integrated floor protection and may therefore be placed
directly on a wooden floor.
Any flooring made of combustible material, such as linoleum,
carpets, etc. must be removed from under the floor plate
Requirement for protecting combustible
flooring in front of fireplace (see fig. 2)
The front plate must be in accordance with national laws and
regulations.
Contact your local building authority regarding restrictions and
installation requirements.
2.2 Walls
Distance from the wall of flammable
material – cf. fig. 1
The fireplace is authorised for use with an uninsulated flue
with the distances to the wall of flammable material as shown
in fig 1.
2.3 Ceiling
There must be a minimum distance of 1000 mm to a combustible
ceiling above the fireplace.
UNITED KINGDOM
3.0 Installation
N.B. Check that the fireplace is free of any damage prior to
commencing installation.
The product is heavy! Make sure you have assistance when
erecting and installing the fireplace.

3.1 Prior to installation

1. Standard product supplied in two packages. One with the
fireplace itself and one with optional base in cast-iron/
concrete/glass or pedestal in cast-iron.
2. When the product is unpacked, the burn plates, baffle plate,
exhaust deflector, base plate, ash pan and riddling grate are
removed. Also remove the small side burn plates and gasket
for flue pipe which are in the ash pan.
3. Lift off the top plate with the top grid
4. Check that the operating handles work.
5. If the rear flue pipe outlet is used, first drill holes
the cut-out covers for the flue pipe before they are knocked
out with the aid of e.g a ball-pane hammer.
6. Place the wooden block
deflectors in position so that the side plates are supported
when the cut-out covers are removed.
7. Spread out the cardboard packaging on the floor. Lay the
stove carefully on its side.
8. If the glass décor set (optional extras) is to be used, the 4
recessed head screws on the bottom are removed (fig. 4B)
with the aid of the key included with the glass décor set.
Supply of external air
With F 370 it is possible to draw external air directly into the
product through the base/pedestal, or through a flexible supply
hose from outside/chimney* and to the outlet of the product
(fig. 4C).
* This shall only apply if the chimney has its own duct for external air.
3.2 Assembly
Jøtul F 371 - cast-iron base - (fig. 4, 6, 7 and 8)
N.B. If the flexible hose is to be connected through a hole in the
floor, the knock out covers are not knocked out/removed.
1. If flexible hose, 100 mm diameter, for external air supply is to
be connected to the outlet under the burn chamber (fig. 4C), drill
one hole (fig. 6A) in each cut-out cover at the lower part of
the base and knock them out. N.B. Make sure the rear plate
(fig. 7 A) in the base is positioned, when the cut-out cover is
being knocked out.
2. Remove rack and rear plate in the base. Check that the handle
in the external air vent (fig. 4D) is in the foremost position.
3. Assemble the base with the burn chamber with the aid of
the 4 screws (M8x30 mm) from the screws bag (fig. 4A).
4. Get assistance and carefully lift the product up.
5. Draw the flexible hose through the hole and fasten it to the
outlet with the aid of a hose clip. N.B. Make sure that the
hose is long enough to avoid any joints.
6. The base area must be protected from heat radiation from
the product with the aid of the accompanying heat shield (fig.
8A). Fasten this with the 2 screws as shown in fig. 8B.
7. Adjust the product with the help of the 4 adjusting screws
(fig. 8C).
8. Reassemble the the rack and the rear plate in the base.
(fig. 21 A) and bowl (fig. 21B).
(fig. 6A) in
(fig. 6B) that holds the exhaust
27