Modular FCG051 Serie Instalación, Uso, Mantenimiento página 28

If it is not necessary to preheat the oven, finished
entering the program, press twice T13 button.
In the case in which after entering the cooking
temperature the remaining parameters are set to
default, push directly T13 button; the oven will start
the cooking cycle.
CORE PROBE COOKING
Once the oven has been switched on by pressing the
T1 key, select the desired cooking mode by pressing
the relative key (T2 - T3 - T4).
Display D1 will alternately flash the LED L1 and L2.
Set cooking temperature pressing T6 button , which
varies depending on the type of the set cooking.
D2 display shows the label "t", rotate "M" knob and
set the label "PRB" to set the cooking with pin.
D2 display shows the value of 30 ° C, which indicates
the desired temperature to reach in the product
core. Turn "M" knob and set the desired value. Press
"M" to confirm.
Display D2 shows the value 0, concerning humidity
required for cooking. Set the required value turning
the "M" and confirm.
D2 display shows the label "CLS" related to the drain
valve.
The setting parameters of the drain valve are two:
CLOSE (CLS)
OPEN (OPN)
Set the desired value by turning the knob "M" and
confirm.
The D3 display shows the label "H" concerning the
fan speed set by default on high. Turn "M" knob to
change the value from High to Low and confirm.
Press T13 button to start preheating the oven. The
temperature to which the oven is preheated is 20 ° C
higher than the set cooking temperature.
The oven will beep once it reaches the temperature.
Insert the food and close the door; the oven will
start the cooking cycle. Otherwise push T13 button.
If it is not necessary to preheat the oven, finished
entering the program, press twice T13 button.
In the case in which after entering the cooking
temperature the remaining parameters are set to
default, push directly T13 button; the oven will start
the cooking cycle.
COOKING WITH ΔT
Once the oven has been switched on by pressing the
T1 key, select the desired cooking mode by pressing
the relative key (T2 - T3 - T4).
Display D1 will alternately flash the LED L1 and L2.
Select the ΔT mode by pressing the T7 key.
The cooking with
temperature at the core of the product and the
cooking chamber temperature.
Set ΔT pressing T7 button; temperature can vary
from 5 to 75 ° C.
D2 display shows the value of 30 ° C, which indicates
the desired temperature to reach in the product
core. Turn "M" knob and set the desired value. Press
"M" to confirm.
D2 display shows the moisture value required for
cooking. Set the required value by turning "M" knob
and confirm.
D2 display shows the label "CLS" related to the drain
valve.
The setting parameters of the drain valve are two:
CLOSE (CLS)
OPEN (OPN)
Set the desired value by turning the knob "M" and
confirm.
The D3 display shows the label "H" concerning the
fan speed set by default on high. Turn "M" knob to
change the value from High to Low and confirm.
Press T13 button to start preheating the oven. The
temperature to which the oven is preheated is 20 ° C
higher than the set cooking temperature.
The oven will beep once it reaches the temperature.
Insert the food and close the door; the oven will
start the cooking cycle. Otherwise push T13 button.
If it is not necessary to preheat the oven, finished
entering the program, press twice T13 button.
In the case in which after entering the cooking
temperature the remaining parameters are set to
default, push directly T13 button; the oven will start
the cooking cycle.
ΔT (Delta-T) mode is particulary indicated for the
cooking of medium and big roast.
28
ΔT set a delta between the