Chicco MEC-6126 V Manual De Instrucciones página 10

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 14
- Do not leave the bottle warmer exposed to atmospheric agents (rain, sun, etc.).
- Never touch the bottle warmer with wet or damp hands.
- Never submerge or wet the plug, the bottle warmer or power cable in water or any other liquid.
- Never touch the bottle warmer if it accidentally falls into water; unplug it immediately and do not use it again; contact
expert qualified operators or Artsana S.p.A. for further instructions.
- If the bottle warmer is faulty and/or not working correctly, switch it off immediately and disconnect the plug from the
mains socket. Do not attempt to open and/or tamper with the product. Contact your retailer or one of Artsana S.p.A.'s
authorised service centres.
- Do not attempt to open or repair the appliance. The bottle warmer can only be opened with special tools. The power
cable must only be replaced with another identical power cable to the one supplied with the appliance; this operation must
be performed by expert technicians or by Artsana S.p.A. only.
- If any repair work is needed, contact expert qualified operators or Artsana S.p.A. only. Incorrect repairs performed by
unauthorised technicians can cause serious damage or injury to users.
When disposing of packaging, parts which wear out or the appliance itself, dispose of them at an appropriate differenti-
ated collection point, as requested by the laws in force in each country.
DESCRIPTION:
a. Display
b. "Feeding Bottle (capacity)/Jar selector button
c. "Food starting temperature" selector button
d. "Timer" button
e. "ON/OFF" button
BEFORE USING THE APPLIANCE.
Never use the bottle warmer without water in the heating tank.
To pour the correct amount of water into the tank, use the feeding bottle which is marked with volume levels
or other suitable recipients. Never place the appliance under running water to fill the tank up.
Check that the power cable plug is always disconnected from the mains socket. Place the bottle warmer on a
flat, stable surface. Pour the correct amount of water into the bottle warmer, making sure you don't exceed the
maximum level.**. Insert the feeding bottle/food jar inside the appliance using the support for smaller baby
food jars/feeding bottles (except for the Chicco Step Up feeding bottle - 330ml). Remove the support from the bottle
warmer before placing the Chicco Step Up - 330ml feeding bottles inside. Make sure that no water overflows from the
top of the appliance; for small sized feeding bottles or jars, check that the water does not reach the top or open mouth of
the same. If water overflows from the bottle warmer when the feeding bottle is placed inside, immediately use a dry cloth
to dry the outside and base of the bottle warmer, then pour out the unneeded water from the tank.
Warning:
Before warming up baby food jars, remove the cap and any labels on the jar.
It is recommended to warm up feeding bottles with the ring and teat in place (not the cup) which will make it
easier to remove the bottle when the warm up cycle is over
.
** see the WATER LEVEL REQUIRED FOR WARM-UP CYCLE chart in the USER INSTRUCTIONS section
Connect the power cable to the appliance and plug it into the mains socket. The appliance will beep when it is connected
correctly (1 beep).
NOTE. After 3 minutes of inactivity or from the end of the "warm-up" cycle, the appliance will switch to "stand-by"
mode and the green led above the main button will blink. To restart the appliance when it is in "stand by" mode, briefly
press and release the "ON/OFF" button.
NOTE. To switch the bottle warmer off, at any time necessary, press and hold the "ON/OFF" button.
USER INSTRUCTIONS
1. Press and hold the ON/OFF button (e) for about 3 seconds to switch the bottle warmer ON.
2. Select the type/capacity of the container to be warmed up by pressing the relative button (b.) until the blue led is
positioned on the desired choice: Jar, Feeding Bottle 150 ml; - Feeding Bottle 250ml; Feeding Bottle - 330ml
3. Select the starting temperature of the food by pressing the relative button (c) until the blue led is positioned on the
desired choice: Ambient temperature (❄ , approx 20°C); Average fridge temperature (❄ ❄, approx 5°C); Average freezer
temperature (❄ ❄ ❄, around -18°C).
4. Press and release the "ON/OFF" button (e.) to start the selected cycle. The red led above the button will come on
10

Publicidad

Tabla de contenido
loading

Tabla de contenido