Tabla de contenido
Publicidad
Enlaces rápidos
Model #
159W
Taylor Barstool
Assembly Instructions
Congratulations!
This fine piece of furniture will make a handsome
addition to your home. For the best results, start by
reading both the Assembly Instructions and
Finishing Hints before you begin your project.
For normal household use only.
recommended for commercial use.
Do not climb stand on this
piece of furniture.
P.O. Box 2827
Eugene, OR 97402 USA
Service Policy:
which are defective, missing or damaged
during assembly. Please contact Whittier
Wood Products customer service department
directly (by phone, fax, mail or email) for
replacement parts.
Hours:
Our friendly customer service staff
can be reached Monday-Friday 7:00 a.m. to
5:00 p.m. (Pacific Time). A message can be
left 24 hours a day, 7 days a week.
To Order:
Provide the complete furniture
model number (upper left corner of this
page), part letter, production code, quantity
needed, reason for replacement and your full
name and address along with a telephone
number in case we need to contact you.
Parts ship from our Eugene, Oregon factory
within 1 or 2 business days from the time
we receive the request. Please allow 5-10
business days for delivery.
Outside U.S. or Canada: 541-687-0213
Outside U.S. or Canada: 541-687-0213
Fax: 541-687-2060 • Email: info@whittierwood.com
Fax: 541-687-2060 • Email: info@whittierwood.com
Mail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
Mail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
Read both the Assembly Instructions and Finishing
Hints completely before beginning.
Store the parts: 1) in their box; 2) in a dry place; 3) in
temperatures ranging from 40° to 90°. (Not on a cold,
possibly damp, cement floor.)
Inspect your furniture periodically for any loose glue
joints or screws, or any other problem which may
be affecting the stability of your furniture. Tighten or
repair as needed.
Production Code:
We will replace any parts
3/05
Publicidad
Tabla de contenido
Manuales relacionados para Whittier Wood Products Taylor 159W
Resumen de contenidos para Whittier Wood Products Taylor 159W
- Página 1 Model # 159W Taylor Barstool Assembly Instructions Service Policy: We will replace any parts which are defective, missing or damaged during assembly. Please contact Whittier Wood Products customer service department directly (by phone, fax, mail or email) for replacement parts. Hours: Our friendly customer service staff can be reached Monday-Friday 7:00 a.m.
- Página 2 159W Taylor Barstool — Parts List BEFORE BEGINNING ASSEMBLY, check that the quantities of the parts received match those on the parts list below. A — Left Leg — Qty. 2 H — Arm Post (9 ") — Qty. 2 B —...
-
Página 3: Tools Required
159W Taylor Barstool ASSEMBLY INSTRUCTIONS TOOLS REQUIRED: Mallet or Padded Hammer, Phillips Head Screwdriver, Wood Glue. IMPORTANT! Once you start gluing the stool together, continue until complete. Before beginning assembly, lay out all the parts to become familiar with their location on the stool. Note that there are two Left Legs and two Right Legs. - Página 4 FIG. 3 3) Apply an even coat of glue to the remaining four holes in each pair of legs. With one pair of legs laying on its side, insert the Short Stretchers into the upper holes and the Long Stretchers into the lower holes.
- Página 5 FIG. 6 6) Glue Arm Posts and Spindles as shown in FIGURE 6. NOTE: A new swivel may appear frozen or hard to turn. It can be loosened by twisting it a little before assembly. Be sure to use a towel or gloves to protect hands as the edges of the swivel may be sharp.
- Página 6 FIG. 9 9) Cover your work surface with a cloth or piece of cardboard to protect the finished seat. Place the seat upside down on the work surface. Be sure the front of the swivel is placed towards the front of the seat, ("FRONT"...
- Página 7 Modelo # 159W Taburete de Bar Normas para obtener servicio: Reemplaza- Taylor remos las piezas que tengan defectos, falten o se dañen durante el armado. Sírvase comunicarse con Instrucciones para Armar el departamento de servicio al cliente de Whittier Wood Products directamente (por teléfono, fax, correo o e-mail) para obtener piezas de repuesto.
-
Página 8: 159W Taburete De Bar Taylor
159W Taburete de Bar Taylor Lista de piezas ANTES DE ENSAMBLAR, verifi que que haya recibido todas las piezas que se listan en la lista de piezas que se presenta a continuación. Parte Descripción Cantidad Parte Descripción Cantidad Parte Descripción Cantidad Pata izquierda . - Página 9 159W Taburete de Bar Taylor orifi cios para las patas; unte una capa uniforme de el respaldo sobre cada larguero, metiéndolos todos pegamento dentro de estos orifi cios. Inserte las cuatro hasta llegar al lado opuesto, tal como se muestra en la FIGURA 7.
- Página 10 No. de modèle 159W Tabouret de Bar Politique de service : Nous remplacerons toutes Taylor les pièces défectueuses, manquantes ou endom- magées pendant le montage. Veuillez contacter Instructions de Montage directement le service clientèle de Whittier Wood Products (par téléphone, fax, courrier ou e-mail) pour obtenir les pièces de remplacement.
-
Página 11: 159W Tabouret De Bar Taylor
159W Tabouret de Bar Taylor Nomenclature des pièces AVANT DE COMMENCER LE MONTAGE, assurez-vous que les quantités des pièces reçues correspondent à la nomenclature des pièces fi gurant ci-dessous. PIÈCE DESCRIPTION QTÉ PIÈCE DESCRIPTION QTÉ PIÈCE DESCRIPTION QTÉ Pied gauche ... . . 2 Montant de bras (9 po) . - Página 12 159W Tabouret de Bar Taylor FIXATION DE L’ASSEMBLAGE DES PIEDS que vous n’ayez mis le dossier en place.) Commencez AU DISQUE : par un côté en frappant légèrement sur le dossier pour le caler sur chaque barreau, jusqu’à ce que vous 4) Pour fixer les pieds, placez le disque (E), dessus face arriviez au côté...