Lutron EcoSystem C5-BMJ-16A Guia De Instalacion página 4

EcoSystem Power Module / Junction Box Mount | Install Guide
Multiple Fixture Dimming Control
Contrôle de gradation de multiples luminaires
Control atenuador de múltiples lámparas
C5-BMJ-16A
Power Indicator (PWR)
Indicateur de puissance (PWR) Indicador de Alimentación (PWR)
On: Unit is powered
On: l'unité est alimentée Encendido: unidad tiene corriente
Off: Unit is not powered
Off: l'unité n'est pas alimentée Apagado: unidad no tiene corriente
or is malfunctioning
ou est dysfonctionnelle o no está funcionando correctamente
Status Indicator (STAT)
Indicateur d'activité (STAT) Indicador de estado (STAT)
Solid: Circuit Level
Plein: Niveau de circuit Sólido: Nivel del Circuito
Pulse: No communication
Impulsion: Aucune Pulsante: No hay comunicación
communication
EcoSystem
Class 2 Sensors
TM
Class 2 Link
Capteurs Classe 2
PWR STAT
Lien Classe 2
Sensores Clase 2
Enlace Clase 2
Multiple Fixture Dimming Control
Contrôle de gradation de multiples luminaires
Control atenuador de múltiples lámparas
C5-BMJ-16A
Power Indicator (PWR) Indicateur de puissance (PWR) Indicador de Alimentación (PWR)
On: Unit is powered On: l'unité est alimentée Encendido: unidad tiene corriente
Off: Unit is not powered Off: l'unité n'est pas alimentée Apagado: unidad no tiene corriente
or is malfunctioning ou est dysfonctionnelle o no está funcionando correctamente
Status Indicator (STAT) Indicateur d'activité (STAT) Indicador de estado (STAT)
Solid: Circuit Level Plein: Niveau de circuit Sólido: Nivel del Circuito
Pulse: No communication Impulsion: Aucune Pulsante: No hay comunicación
communication
EcoSystem
Class 2 Sensors
TM
Class 2 Link
Capteurs Classe 2
PWR STAT
Lien Classe 2
Sensores Clase 2
Enlace Clase 2
Multiple Fixture Dimming Control
Contrôle de gradation de multiples luminaires
Control atenuador de múltiples lámparas
C5-BMJ-16A
Power Indicator (PWR) Indicateur de puissance (PWR) Indicador de Alimentación (PWR)
On: Unit is powered On: l'unité est alimentée Encendido: unidad tiene corriente
Off: Unit is not powered Off: l'unité n'est pas alimentée Apagado: unidad no tiene corriente
or is malfunctioning ou est dysfonctionnelle o no está funcionando correctamente
Status Indicator (STAT) Indicateur d'activité (STAT) Indicador de estado (STAT)
Solid: Circuit Level Plein: Niveau de circuit Sólido: Nivel del Circuito
Pulse: No communication Impulsion: Aucune Pulsante: No hay comunicación
communication
EcoSystem
Class 2 Sensors
TM
Class 2 Link
Capteurs Classe 2
PWR STAT
Lien Classe 2
Sensores Clase 2
Enlace Clase 2
www.lutron.com /support
Occupant Sensor Wired to
Power Module
Black
Red
Blue
EcoSystem Daylight Sensor
and Wallstation wired to the
Power Module (IR wired only
to keypad)
Black
Red
White
Yellow
EcoSystem Daylight Sensor
wired to the Power Module
Black
Red
White
Yellow
Step 6: Addressing the Power Module
(Flash Mode)
• Follow standard procedure for addressing the
EcoSystem Bus
• Each Power Module communicates to the system
the same as an EcoSystem ballast; representing one
(1) address location on the EcoSystem Bus
• Flash Mode (during addressing/programming):
– C5-BMJ-16A: Device will flash the load(s) by
dimming the lights up and down similar to
EcoSystem ballasts.
– C5-XPJ-16A: Device will flash the load(s) by
turning the loads ON and then OFF slowly
(non-dim loads). Do not use this module for HID
loads as it may damage the lamps.
– STAT and LED will flash at same rate as the
loads.
Step 7: Troubleshooting
Module not responding
If the module, attached ballasts, and lamps are
fixed at full-light output, will not dim, and can not be
turned off, the Power Module is likely in emergency
mode or is not communicating. If there is no
communication, the status (STAT) LED will blink.
Verify that the EcoSystem Bus wiring is properly
terminated, powered via the EcoSystem Bus Power
Supply, and 18 V- is present between the E1
and E2 terminals on the Power Module.
Lights Not Dimming
If the lights switch only between off and full‑light
output:
A. Verify the wiring between the module and the
ballast.
B. Verify that the device is a C5-BMJ-16A, because
the C5-XPJ-16A does not offer dimming control.
Lights Stay at Low‑End:
A. Make sure Dimmed Hot is connected
(C5-BMJ-16A only).
B. If most of the ballasts are at low-end and one or
more ballasts are OFF, there is a miswire between
Hot and Dimmed Hot at one of the ballasts that
is OFF. Verify wiring.
Lutron, EcoSystem, Eco-10, and Hi-lume are trademarks of Lutron Electronics Co., Inc.,
registered in the U.S. and other countries.
© 2013-2017 Lutron Electronics Co., Inc.
Lutron Electronics Co., Inc
7200 Suter Road
Coopersburg, PA 18036-1299
USA
4
®