Publicidad
Idiomas disponibles
Idiomas disponibles
KIT COMPONENTS
• A) ISO DDIN trim plate • B) ISO DDIN brackets
A
B
The World's best kits.
®
Subaru Legacy/Outback
KIT FEATURES
• ISO DDIN radio provision
• Painted scratch resistant matte black
Note: Minor sub-dash modifications required.
Part # 95-8903B does not require these modifications
MetraOnline.com
2010-2014
(non nav models)
© COPYRIGHT 2017 METRA ELECTRONICS CORPORATION
95-8904B
I N S TA L L AT I O N I N S T R U C T I O N S
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Assembly
– ISO DDIN radio provision ....................................3
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: Please visit metraonline.com
for wiring harness options.
Antenna Adapter: Please visit metraonline.com
for antenna adapter options.
Steering Wheel Control Interface: ASWC-1
TOOLS REQUIRED
• Panel Removal Tool • Phillips Screwdriver
• Cutting Tool
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
REV. 9/19/17 INST95-8904B
Publicidad
Tabla de contenido
Manuales relacionados para Metra 95-8904B
Resumen de contenidos para Metra 95-8904B
- Página 1 Also, do not remove the factory radio with the key in the on position, or while the vehicle is running. The World’s best kits. MetraOnline.com ® © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 9/19/17 INST95-8904B...
-
Página 2: Dash Disassembly
DASH DISASSEMBLY 1. Unclip and remove the radio trim panel including the a/c vents. (Figure A) 2. Remove (4) Phillips screws securing the radio, then unplug and remove the radio. Continue to Kit Assembly (Figure A) 1.800.221.0932 MetraOnline.com... -
Página 3: Kit Assembly
4. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or AXXESS. Test the radio for proper operation . 5. Reassemble the dash in reverse order of disassembly. - Página 4 Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians The World’s best kits. MetraOnline.com ® © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 9/19/17 INST95-8904B...
- Página 5 Además, no quite el radio de fábrica con la llave en la posición o de encendido ni con el vehículo funcionando. The World’s best kits. MetraOnline.com ® © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 9/19/17 INST95-8904B...
-
Página 6: Desmontaje Del Tablero
DESMONTAJE DEL TABLERO 1. Desenganche y quite el panel de la moldura del radio incluyendo las rejillas. (Figura A) 2. Quite los (4) tornillos Phillips que sujetan el radio, luego desconecte y retire la radio. Continúe con el Ensamble del Kit (Figura A) 1.800.221.0932 MetraOnline.com... -
Página 7: Ensamble Del Kit
Metra recomienda que use adaptadores adecuados de acoplamiento de Metra y/o de AXXESS. Pruebe el radio para verificar que funcione correctamente. 5. Vuelva a armar el tablero al revés de como lo desarmó. - Página 8 800-354-6782 para obtener más información y avance hacia un futuro mejor. Metra recomienda técnicos con certificación del Programa de Certificación en Electrónica Móvil (Mobile Electronics Certification Program, MECP). The World’s best kits. MetraOnline.com ® © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 9/19/17 INST95-8904B...