Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Toyota 4-Runner Limited
KIT FEATURES
• Double DIN radio provision
KIT COMPONENTS
• A) Double DIN trim plate • B) Double DIN brackets
A
B
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-1761 • TYTO-01
Antenna Adapter: • Not required
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver • 10 mm socket removal tool
METRA. The World's best kits.
INSTALLATION INSTRUCTIONS FOR PART 95-8210
(without navigation)
95-8210
™
metraonline.com
2003-2009
Dash Disassembly ................................................. 2
Kit Assembly
–
CAUTION!
tery terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your local
Dealership for more information. All accessories, switches, climate
controls panels, and especially air bag indicator lights must be con -
nected before reconnecting the battery or cycling the ignition. Also,
do not remove the factory radio with the key in the on position, or the
vehicle running. It would be best to remove the key from the ignition
and then wait a few seconds before removing the factory radio.
Table of Contents
Double DIN radio provision
............................... 3
Metra recommends disconnecting the negative bat -
© COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION
Publicidad
Manuales relacionados para Metra 95-8210
Resumen de contenidos para Metra 95-8210
- Página 1 KIT COMPONENTS • A) Double DIN trim plate • B) Double DIN brackets CAUTION! Metra recommends disconnecting the negative bat - tery terminal before beginning any installation, unless the vehicle manufacturer recommends against so. Please check with your local WIRING & ANTENNA CONNECTIONS (sold separately) Dealership for more information.
- Página 2 95-8210 Dash Disassembly 1. Unsnap and remove trim from 6. Remove (1) 10 mm bolt beneath around shifter. (Figure A) climate control behind pocket door. (Figure E) Unsnap climate control, 2. Unsnap and remove center console unplug and remove climate control.
- Página 3 (Figure C) (Figure B) 4. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation.
- Página 4 INSTALLATION INSTRUCTIONS FOR PART 95-8210 IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated.
- Página 5 HERRAMIENTAS REQUERIDAS cuantos segundos antes de quitar el radio de fábrica. • Herramienta para quitar paneles • Destornillador Phillips • Herramienta de remoción de casquillo de 10 mm METRA. The World’s best kits. metraonline.com ™ © COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION...
- Página 6 95-8210 Desmontaje Dash 1. Suelte a presión y retire la moldura 6. Quite (1) perno de 10 mm de abajo de alrededor de la palanca de del control de clima, detrás de velocidades. (Figura A) la puerta de la cavidad. (Figura E) Suelte a presión el control de...
- Página 7 (Figura C) (Figura B) 4. Localice el arnés de cables de fábrica en el tablero. Metra recomienda el uso de un adaptador adecuado de acoplamiento de Metra o de AXXESS. Vuelva a conectar la terminal negativa de la batería y pruebe la unidad para...
- Página 8 800-354-6782 para obtener más información y avance hacia un futuro mejor. Metra recomienda técnicos con certificación del Programa de Certificación en Electrónica Móvil (Mobile Electronics Certification Program, MECP). METRA. The World’s best kits. metraonline.com ™ © COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION...