Heating Liquids Using The Steam Function; Cleaning And Maintenance - FAR EC-15 CI Manual De Instrucciones

ENGLISH

HEATING LIQUIDS USING THE STEAM FUNCTION

The steam wand (without the foamer) can be used to make hot drinks, like hot
chocolate, hot water or tea.
Method:
Open the water tank lid, pour the water into the tank in line with the steps outlined
1.
above, then close the water tank lid.
Plug in the appliance; "12:00" is displayed on the screen. Check that the steam knob
2.
is in the "OFF" position.
Press the button for the espresso function. The red light comes on and the green
3.
light flashes. When the water flows out, press the
the pump immediately. Then press the
The appliance begins pre-heating.
When the green light remains on, pre-heating is finished.
4.
Note: If the green light flashes during use, you must turn the steam knob to the
"OFF" position and press the button (first check that there is water in the
tank), then switch off the pump after approximately 20 seconds; wait until the
green light comes on again, then turn the steam knob anti-clockwise to release
the steam again.
Remove the foamer from the steam wand.
5.
Dip the steam wand into the liquid to be heated. Turn the steam knob anti-
6.
clockwise slowly.
Once the desired temperature is reached, turn the steam knob to the "OFF" position.
7.
Press the button once to switch off the coffee maker.
8.

CLEANING AND MAINTENANCE

Switch off the electrical supply and leave the coffee machine to completely cool
1.
down before cleaning.
Regularly clean the coffee maker unit with a sponge, and regularly clean the hot
2.
plate and removable grille, then leave it to dry completely.
Note: Do not clean the appliance with alcohol or a solvent. Do not immerse
the unit in water to clean it.
Remove the metal filter holder by turning it clockwise. Empty out the coffee
3.
grounds then clean it, and rinse it gently after cleaning.
Clean all of the removable accessories in water and dry them completely.
4.
GB-12
button and switch off
button. The green light flashes.
DESCALING (espresso-making system)
To guarantee your coffee maker's operational efficiency, the cleanliness of internal
1.
pipes and the taste of the coffee, remove mineral deposits every 2 - 3 months.
Fill the water tank with water and limescale remover to the maximum level
2.
(the ratio of water to limescale remover must be 4 to 1. Follow the limescale
remover instructions). Use a "household limescale remover". You can also use citric
acid (available in shops) instead of limescale remover (the ratio of water to citric
acid must be 100 to 3).
Depending on the pre-heating program, insert the metal filter holder (without
3.
the ground coffee) and the coffee pot. Heat the water by following the steps in
the "PRE-HEATING" section.
Press the button for the espresso function. The function light (red) comes on
4.
and the green light flashes. When the water starts to flow, press the
switch off the pump and wait a moment. The coffee maker will start to heat up.
When the green light remains on, pre-heating is finished. Press the
5.
and make two cups of coffee (approximately 57 g). Then switch off the pump and
wait 5 seconds.
Press the button so that the green
6.
remains on. Turn the steam on for 2 minutes, then turn the steam knob to the
"OFF" position to stop the steam. Press the button to switch off the appliance
immediately and leave the limescale remover solution to act in the appliance for
approximately 15 minutes.
Switch on the appliance again and repeat steps 4 to 6 at least 3 times.
7.
Then press the button so that the green
8.
light to remain on, then press the button to infuse it until there is no more
limescale solution left.
Then switch on the appliance (without ground coffee). Using running water, fill the
9.
tank up to the maximum level, repeat steps 4 to 6 three times (it is not necessary to
wait 15 minutes at step 6), then run the appliance until there is no water left in the
tank.
Repeat step 9 at least 3 times to ensure that the pipes are clean.
10.
DESCALING (filter coffee-making system)
Fill the tank with water and limescale remover to the maximum level (i.e.
1.
approximately 1.25 L; the ratio of water to limescale remover must be 4 to 1.
Follow the limescale remover instructions). Use a "household limescale remover".
You can also use citric acid instead of limescale remover (the ratio of water to
citric acid must be 100 to 3).
ENGLISH
button,
button again
light flashes, then wait until it
light flashes. Wait for the green
GB-13