Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
TRANSMITTER DATA STORAGE AND
SELECTION OF THE SUNSHADE/ROLL-UP
SHUTTER MODE
m
CAUTION: The data storage of the first transmitter
determines the direction of motion of the motor.
To store a transmitter on a virgin control untit proceed as
follows:
1.
Supply power only to the control unit to be programmed
2.
Activate the LOKI programming
3.
To select the SUNSHADE mode press the UP or DOWN keys
until the led performs n. 1 flash
To select the ROLL-UP SHUTTER mode press the UP or DOWN
keys until the led performs n. 2 flashes.
4.
Press the UP+DOWN keys until the motor starts to move in
one direction
5.
Release the keys, the motor stops
6.
Press the UP or DOWN keys according to the direction in
which the roll-up shutter was moving before it stopped:
- if the roll-up shutter was being raised press the UP key;
direction obtained: the UP key raises the roll-up shutter, the
DOWN key lowers the roll-up shutter
- if the roll-up shutter was being lowered press the DOWN
key; direction obtained: the DOWN key lowers the roll-up
shutter, the UP key raises the roll-up shutter.
7.
To exit the programming mode press the STOP key
8.
Try to operate the roll-up shutter and verify that it works
according to the logic described above. If the logic is reversed
it is necessary to delete all the codes stored (see "DELETION
OF ALL MEMORIZED TRANSMITTERS") and repeat the steps
above.
To add other remote controls you can also use the "QUICK
MEMORIZATION OF TRANSMITTERS
DELETION OF ALL MEMORIZED
TRANSMITTERS
To delete all codes stored with an LOKI proceed as follows:
1.
Supply power only to the control unit to be programmed
2.
Activate the LOKI programming
3.
Press the UP or DOWN keys until the led performs n. 3 flashes
4.
Press and hold down the UP+DOWN keys until the motor
moves in both directions which confirms the correct deletion
of the codes.
5.
Release the keys
6.
To exit the programming mode press the STOP key
To delete all codes NOT stored with an LOKI proceed as
follows:
1.
Cut the power to the motor on which to delete all the codes
2.
Activate the LOKI programming
3.
Press the UP or DOWN keys until the led performs n. 3 flashes
4.
Press and hold down the UP+DOWN keys
5.
Power the motor and wait until the motor moves in both
directions wich confirms the correct deletions of the codes
6.
To exit the programming mode press the STOP key
PROGRAMMING THE UPPER POSITION OF
THE END-OF-STROKE
To set the upper position of the end-of-stroke sensor on a
roll-up shutter equipped with lock on the upper side it is
necessary to use a remote control previously stored and
proceed as follows:
1.
Supply power only to the control unit to be programmed
2.
Activate the LOKI programming
3.
Press the UP or DOWN keys until the led performs n. 4 flashes
4.
Press and hold down the UP+DOWN keys until the motor
moves in both directions which confirms it is entering the
programming phase
5.
Release the keys, the motor stops
6.
Press the UP key: the roll-up shutter rises at a normal speed
7.
Once in contact with the upper lock, it stops and memorizes
the position
8.
To exit the programming mode press the STOP key
To set the upper position of the end-of-stroke sensor on a
roll-up shutter equipped without lock on the upper side it
is necessary to use a remote control previously stored and
proceed as follows:
Repeat points 1,2,3,4 previously described
6.
Bring the roll-up shutter to the upper position desired using
the UP and DOWN keys. To regulate it precisely, press the
UP+DOWN key when the motor is close to the end-of-stroke:
the motor will start to move in jerks
7.
Press the STOP button when the desired position is reached
8.
To exit the programming mode press the STOP key
PROGRAMMING THE LOWER POSITION OF
THE END-OF-STROKE
To set the lower position of the end-of-stroke it is necessary
to use a remote control previously stored and proceed as
follows:
1.
Supply power only to the control unit to be programmed
2.
Activate the LOKI programming
3.
Press the UP or DOWN keys until the led performs n. 5 flashes
4.
Press and hold down the UP+DOWN keys until the motor
moves in both directions which confirms it is entering the
programming phase
5.
Release the keys, the motor stops
6.
Bring the roll-up shutter to the LOWER position desired
using the UP or DOWN keys. To regulate it precisely, press
the UP+DOWN keys when the motor is close to the end-of-
stroke: the motor will start to move in jerks
7.
Press the STOP button when the desired position is reached
8.
To exit the programming mode press the STOP key
- 9 -
Publicidad
Tabla de contenido
