Electric Power - Sammic AG-20 Manual De Instrucciones

INSTALLATION
Warning
THIS APPLIANCE MUST BE INSTALLED BY A
SPECIALIST TECHNICIAN ACCORDING TO
THE LAWS AND REGULATIONS IN FORCE IN
THE COUNTRY OF DESTINATION, IN WHICH
THE APPLIANCE WILL BE USED.
Safety Rules for Installation
This appliance cannot be connected to a duct
for removing the products of combustion.
It must be installed and connected accor-
ding to the regulations in force.
Particular care must be taken with the ven-
tilation systems you use.
The installation, connection and mainte-
nance must be undertaken only by a spe-
cialist technician, taking into account all
the present instructions, as well as all the
remaining provisions concerning the site of
installation:
- An adequate flow of air in and out of the
area is needed.
- A site of at least 64m³ is required.
- A window, opening to at least 0.40m² is
required.
Installation and use of this appliance in
basement areas is prohibited.
The installation, use and maintenance of
this appliance by children is strictly prohi-
bited. Keep children and curious onlookers
away when the appliance is in operation.
The appliance must be installed on a hori-
zontal surface, with a constant heat resis-
tance of at least 90° C. All flammable sur-
faces are prohibited.
A space of 0.20m must be left around the
appliance for ventilation.
Do not hang anything over the appliance at
a distance of less than 1.5 metres, because
6 EN
the temperature above the exhaust duct (2)
Figure A, is very high.
The height of the surface on which the
appliance is to be sited must be between
0.70m and 0.90m from the floor.
Connection
The appliance may be connected in three ways,
depending on the type of gas to be used.
The connection port (4) Figure B, between
the appliance and the gas supply is situa-
ted at the back side of the appliance.
Use of the Appliance with Butane and
Propane
Butane: Use an approved low pressure
regulator 28 - 30mbar.
Propane: Use an approved low pressure
regulator 37mbar.
In this case, you may use the connection
nozzle (1), Figure B, which accompanies the
appliance, to connect it with a flexible pipe.
Screw the nozzle on the backside of the
appliance, on the gas connection port (4),
with a diameter of 16 mm (3/8).
This pipe must be recognized for this use.
You must check the date of replacement of
the pipe.
You must install it in such a way that it is
visible along its whole length (from the
appliance to the supply tap or to the bottle).
The connections must be checked for leaks
in order to avoid gas escaping, with the
help of soapy water.
To do so: open the bottle or the supply-
tap, to allow the gas to circulate, and ensu-
re that the connection is correct by chec-
king for air bubbles in the soapy water
spread over the connections.
DANGER: THE USE OF A FLAME TO CHECK
FOR LEAKS AT CONNECTION POINTS IS
STRICTLY FORBIDDEN.
Use of the Appliance with Natural Gas
Connection may be made with the help of
the nozzle (2), Figure B, when a flexible
pipe is to be used, following the instruc-
tions on the previous paragraph with
regard to connection instructions and
checking for leaks.
If you wish to make a permanent, fixed
connection with a metallic pipe screwed
into position, it will be necessary to use the
nozzle (3), Figure B.
This is the recommended type of connec-
tion.
DANGER: THE USE OF A FLAME TO CHECK
FOR LEAKS AT CONNECTION POINTS IS
STRICTLY FORBIDDEN
Use of the Appliance with Propane &
Butane 50 mbar
Butane: Use an approved low pressure
regulator 50 mbar
Propane: Use an approved low pressure
regulator 50 mbar
Connection may be made with the help of
the nozzle (1), Figure B, when a flexible pipe
is to be used, following the instructions on
paragraph 3.1 with regard to connection
instructions and checking for leaks.
If you wish to make a permanent, fixed
connection with a metallic pipe screwed
into position, it will be necessary to use the
nozzle (3), Figure B.
This is the recommended type of connec-
tion.
DANGER: THE USE OF A FLAME TO CHECK
FOR LEAKS AT CONNECTION POINTS IS
STRICTLY FORBIDDEN
ELECTRIC POWER: The appliance is connec-
ted to the mains using a security socket,
230 V, 50 Hz, earthed.