Safety Precautions - 3M 28338 Manual De Instrucciones

Safety Precautions

1. Read all instructions before using this tool. All operators must be fully
trained in its use and aware of these safety rules.
2. The tool RPM should be checked on a regular basis to ensure proper
operating speed.
3. Make sure the tool is disconnected from the air supply. Select suitable
abrasive, mounting hardware and accessories and secure them to the
spindle. Be careful to center the abrasive & mounting hardware.
4. Always wear required safety equipment when using this tool.
5. Always remove the air supply to the sander before fitting, adjusting or
removing the abrasive & mounting hardware.
6. Always adopt a firm footing and grip and be aware of torque reaction
developed by the sander.
7. Use only 3M approved spare parts.
8. Always ensure the material being worked is firmly fixed to avoid
movement.
9. Check hose and fittings regularly for wear. Do not carry the tool by its
hose; always be careful to prevent the tool from being started when
carrying the tool with the air supply connected.
10. Dust is highly combustible.
11. If tool is serviced or rebuilt check to ensure that the maximum tool RPM
is not exceeded and that there is no excessive tool vibration.
12. Do not exceed maximum recommended air pressure. Use safety
equipment as recommended.
13. Prior to installing any abrasive, wheel or mounting hardware, always
check that their marked maximum operating speed is equal or higher
than the rated speed of this tool.
14. The tool is not electrically insulated. Do not use where there is a
possibility of contact with live electricity, gas pipes, and/or water pipes.
15. This tool is not protected against hazards inherent in grinding and
cutting operations, which require a guard, and no such grinding and
cutting products should ever be attached.
16. Take care to avoid entanglement with the moving parts of the tool with
clothing, ties, hair, cleaning rags or loose hanging objects. If entangled,
stop air supply immediately to avoid contact with moving tool parts.
17. Keep hands clear of the spinning abrasive & mounting hardware or
spindle during use.
18. If the tool appears to malfunction, remove from use immediately and
arrange for service and repair.
19. Immediately release the start handle in the event of any disruption
of pressure; do not attempt to restart until the disruption has been
corrected.
20. Do not allow the tool to free spin without taking precautions to protect
any persons or objects from debris from rupturing abrasive & mounting
hardware.
21. When tool is not in use, store in a clean dry environment free of debris.
22. Recycle or dispose of tool according to Local, State, and Federal
regulations.
Drain Leg
Ball Valve
To Tool Station
Ball
Valve
Drain Valve
To Coupler
at or near Tool
Closed Loop Pipe System
Sloped in the direction of air flow
Filter
Regulator
Lubricator
Ball Valve
Air Hose
Air Compressor
and Tank
Figure 1
3M™ Inline Sander Accessories
3M™ Inline Sander accessories are designed for use on 3M Inline Sanders.
Constructed from premium, industrial-quality materials, their durability and
precise construction are the ideal complement to the performance of the 3M
Inline Sander. See Product Configuration/Specifications table for mounting
information for a particular model.
3M™ Rubber Slotted Expander Wheel, 5 in x 3 ½ in x
Arbor Hole (for 3 ½ in x 15 ½ in belts)
3M™ Rubber Slotted Expander Wheel, 3.4 in x 3 in x
Arbor Hole (for 3 in x 10
3M™ Wheel Adaptor Kit #3,
See 3M ASD Accessory catalogs 61-5002-8098-9 and 61-5002-8097-1 for
additional Accessories.
3M Inline Sander: Instructions for Mounting
and Dismounting Hardware
Rubber Slotted
Expander Wheel
5 in x 3 1/2 in
1. Disconnect air line from tool.
2. If already mounted, remove spindle mounted accessories and/or
abrasive product by using the wrenches supplied with the tool. Use the
wrenches to hold the tool spindle while turning the spindle extension
and/or mounting hardware counter clockwise.
3. Fully thread new spindle mounted accessories and/or abrasive product
onto the spindle in a clockwise rotation.
4. Secure all spindle mounted accessories and/or abrasive product with the
wrenches and tighten the spindle nut securely. Always use the correct
sized spindle accessories with the matching thread pitch and diameter.
An inadequately secured accessories and/or abrasive product could
loosen, bend or break causing damage to the tool and work piece and
possible injury to the operator or bystanders.
5. After the spindle accessories and/or abrasive product have been
Air Flow
mounted, inspect them to ensure they are free of debris and
undamaged.
6. Re-connect air line, position tool in a safe location, and test for any
unusual noise or vibration which may be caused by damaged or
improperly mounted accessory and/or abrasive product.
Air Dryer
Note: During the above steps, ensure that all hardware and abrasive
products are mounted concentrically on the supporting accessory.
6
Accessory Description
11
/ in belts)
16
5
/ -11 External
8
3/8 in Spacer
Properly Sized Abrasive Belt
Rubber Slotted
Expander Wheel
Spindle Nut
3.4 in x 3 in
Part
Number
5 /
8
28348
5 /
8
28349
45038
3/8 in Spacers