Publicidad
Idiomas disponibles
Idiomas disponibles
5.Pass the diagonal seat belt trough Height adjuster lever K.
Check that the seat belts are not twisted and tighten by pulling
the diagonal seat belt upwards (4.5).
6. Make sure the vehicle's safety belt is not twisted, also check that
the seat cover does not impede the movement of the vehicle seat
belt or prevent the installation of the seat in any way. To release
your child unbuckle the vehicle safety belt as described in the
instructions.
5. ADJUST THE HARNESS TO THE HEIGHT OF THE CHILD.
Always check that the harness straps are suitable for the height of
your child. The shoulders of the child should always be just below
the back slots at a suitable height (5.1).
Changing the harness height
1. Adjust the height of the harness, by pressing the harness
adjustment button and pulling the harness straps towards you to
loosen them (5.2).
2. Then unhook one of the harness connector straps at the back
of the seat and pull the loose strap towards the front of the seat
(5.3 y 5.4).
3. Insert the harness strap into the slot of the fabric and backrest
at the front of the seat. Then insert the harness strap into the
appropriate upper or lower slot at the rear of the seat (5.5).
4. Reinsert the harness strap in the harness connector on the back
of the seat. At the same time reinsert the harness protective tape
to the harness connector protector (5.6).
5. Then, do the same with the other harness strap. Verify that the 2
harness straps go through the slots at the same height. Do not
use the upper guides of the child seat. These should only be used
to guide the vehicle's safety belts.
Fastening the harness
1. Join the 2 buckle metal connectors (5.7).
2. Pass both connectors through the slot in the upper part of the
buckle until you hear a "click" (5.8).
3. Always make sure the harness is properly fastened by pulling the
harness straps upwards.
Child restraint system
22
4. To unfasten the harness press the red button on the buckle
downwards (5.9).
Tightening the harness
1. Pull the harness straps up to remove the slack from the lap
section of the harness, then pull the harness regulating strap until
the harness is fully stretched (5.10).
2.The harness should be as tight as possible without causing
discomfort to your child.
3. Make sure the lap section of the harness is positioned as low
as possible, surrounding your child's hips and not his stomach.
4. A harness that is not properly tightened can be dangerous.
Check the harness adjustment and tighten whenever you put
your child in the child safety seat.
Loosening the harness
1. The harness is loosened by pressing the adjustment button of the
harness (under the seat cover) at the front of the seat. (5.11)
2. Press the lever that is marked with "press" down with one hand
while holding both harness straps with your other hand.
3. Pull the harness straps towards you to loosen the harness.
4. Be careful when adjusting the harness strap not to trap the
harness adjustment strap when you press the button down.
6. SEAT AND HARNESS REMOVAL.
Remove the seat harness
1. Pull the base tape to detach it from the seat (6.1).
2. From the back of the seat, unhook the harness protector
connector tapes and detach the harness from the metal
connector of the harness, pull the connector tape to detach
completely from the seat (6.2, 6.3, 6.4 y 6.5).
Remove the cover buckle protector and the lower harness
1. Turn the plate attached to the safety buckle so that they coincide
with the nearest slot and insert into the slots of the seat base and
then pass through the slots in the cover (6.6 y 6.7).
BEL123
Group 1/2/3
EN
www.babyqs.com
23
Publicidad
