Technical Data; Safety Instructions For Batteries; Electrical Data - Makita REMS Curvo Instrucciones De Servicio

g
tool. Power tools are dangerous in the hands of untrained users.
accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
Use of the power tool for operations different from those intended
could result in a hazardous situation.
5) Battery tool use and care
that is suitable for one type of battery pack may create a risk of re when used
with another battery pack.
other battery packs may create a risk of injury and re.
terminals together may cause burns or a re.
irritation or burns.
6) Service
This will ensure that the safety of the power tool
is maintained.
WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in electric shock, re and/or serious injury.
Save all warnings and instructions for future reference.
Use personal safety equipment (protective glasses).
Avoid abnormal posture, do not lean too far forward.
Do not reach between the pipe and the bending former when bending. Danger
of crushing !!
Keep hair and clothing clear of moving parts.
Only perform work for which the machine is intended.
Keep third persons away from the working area during work.
The drive machines develop a very high bending force. So be very careful.
The Ni-Cd and Li-Ion batteries cannot be interchanged in the drive unit.
If it is necessary to change the plug or the connecting cable, this should only be
done by the manufacturer or his customer service.

Safety instructions for batteries

WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in electric shock, re and/or serious injury.
Save all warnings and instructions for future reference.
Batteries may only be used at battery or ambient temperatures of –10 °C – +60
°C (14 °F – +140 °F).
The rapid charger may only be used at rapid charger or ambient temperatures
of 0 °C – +40 °C (32 °F – +104 °F).
Observe the safety instructions printed on the battery and the charger.
Do not throw defective batteries in the normal household waste. Hand the defec-
tive batteries over to an authorised REMS contract service workshop or a
recognised disposal company.
Protect battery from getting wet.
Cover the battery contacts when storing outside the tool or rapid charger.
Do not open the battery. Danger of explosion and re due to short-circuit.
Do not modify the construction of the battery.
Only use the battery indoors.
Do not use he battery in adverse ambient conditions, e.g. ammable gases,
solvents, dust, fumes, wet.
Do not use the battery if the housing or contacts are damaged.
Do not use the battery in areas where there is a danger of explosion.
Observe the safety instructions printed on the battery and the charger.
Read the operating instructions before use
Power tool complies wi h protection class II
Environmentally friendly disposal
CE conformity mark
Many
A charger
Use of any
Shorting the battery
Liquid ejected from the battery may cause

1. Technical Data

Use for the intended purpose
WARNING
REMS Curvo and REMS Akku-Curvo are intended for the purpose of cold draw
bending of pipes up to 180°.
REMS Curvo 50 is intended for cold draw bending of pipes up to 90°.
All o her uses are not for the intended purpose and are prohibited.
REMS Curvo drive unit
REMS Akku-Curvo drive unit Li-Ion
REMS Curvo 50 drive unit
Square driver 35 – 50, support 35 – 50
Square driver 10 – 40, support 10 – 40
Insert bolt
Rapid charger Li-Ion/Ni-Cd 230 V, 50 – 60 Hz, 65 W
REMS battery Li-Ion 18 V, 2.6 Ah
REMS battery Li-Ion 18 V, 3.5 Ah
REMS bending spray, 400 ml
1.2. Capacity
No cracks or wrinkles shall occur during professional cold bending. Pipe quali-
ties and sizes which do not guarantee this are not suited to be bent with REMS
Curvo, REMS Curvo 50 and REMS Akku-Curvo.
Hard copper pipes are cold bendable up to Ø 18 mm according to DIN EN
1057, minimum radii must be complied wi h. Bending formers and back formers
for larger bending radii can be supplied.
REMS Curvo
Hard, half-hard, soft copper pipes, also thin walled, Ø 10 – 35 mm,
Soft, jacketed copper pipe, also thin walled, Ø 10 – 18 mm.
Stainless steel pipes of the press tting systems Ø 12 – 28 mm.
acketed C-steel pipes of the press tting systems Ø 12 – 28 mm.
Soft precision steel pipes Ø 10 – 30 mm, wall thickness 1.5 mm.
Steel pipes DIN EN 10255 (DIN 2440) ¼" – ¾".
Electrical installation pipes DIN EN 50086 Ø 16 – 32 mm.
Composite pipes Ø 14 – 40 mm.
Largest bending angle
REMS Curvo 50
Steel pipes as per DIN EN 10255 (DIN 2440) ¼" – 1¼".
Hard, half-hard and soft copper tubes Ø 10 – 42 mm.
Thin walled copper tubes Ø 10 – 35 mm.
Stainless steel tubes of press tting systems Ø 12 – 42 mm.
Composite tubes Ø 14 – 50 mm.
Largest bending angle
REMS Akku-Curvo
Hard, half-hard, soft copper pipes, also thin walled, Ø 10 – 28 mm,
Soft, jacketed copper pipe, also thin walled, Ø 10 – 18 mm.
Stainless steel pipes of the press tting systems Ø 12 – 28 mm.
acketed C-steel pipes of the press tting systems Ø 12 – 28 mm.
Soft precision steel pipes Ø 10 – 28 mm, wall thickness 1.5 mm.
Steel pipes DIN EN 10255 Ø ¼ – ½".
Electrical installation pipes DIN EN 50086 Ø 16 – 25 mm.
Composite pipes Ø 14 – 32 mm
Largest bending angle
1.3. Speed Curvo
Speed in nitely
adjustable 0...4 min

1.4. Electrical data

REMS Curvo, 230 V, 1~, 50 – 60 Hz; 1000 W; 4.8 A or
REMS Curvo 50 110 V, 1~, 50 – 60 Hz; 1000 W; 9.6 A,
Intermittent service S3 15% 2/14 min,
double insulated, interference-suppressed.
Protection class IP 20
REMS Akku-Curvo 18 V =
Rapid charger (1 h) Input
Output
L×W×H: 585×215×140
(23"×8½"×5½")
1.6. Weights
Drive unit 8.3 kg
(18.3 lb)
Bending former 0.2..1.6 kg
(½..3½ lb)
Back former 0.1..0.2 kg
(¼..½ lb)
Insert bolt 0.4 kg ( lb)
g
580000
580002
580100
582110
582120
582036
571560
565215
565217
140120
–1 ".
180°
90°
– 1 ".
180°
Curvo 50 Akku-Curvo
0...1 min 0...3,33 min
230 V~; 50 – 60 Hz; 65 W
12 –18 V =
640×240×95 540×280×140
(25"×9½"×3¾") (21¼"×11"×5½")
16.9 kg 9 kg (wi h batt.)
(37.3 lb) (19.8 lb)
4.44..7.8 kg 0.2..1.6 kg
(9.8..17.2 lb) (½..3½ lb)
0.25..0.42 kg 0.1..0.2 kg
(0.55..0.9 lb) (¼..½ lb)
0.4 kg ( lb) 0.4 kg ( lb)