Black and Decker PRO Serie Manual De Instrucciones página 12

Ocultar thumbs Ver también para PRO Serie:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

ENGLISH
cutting tools with sharp cutting edges are less likely to bind
and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth wire
is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must be
replaced by the manufacturer, authorized
Black & Decker Service Center or an equally qualified
person in order to avoid damage or injury. If the power
cord is replaced by an equally qualified person, but
not authorized by Black & Decker, the warranty will
not be valid.
7. Labels on tool
The label on your tool may include the following symbols:
Read Instructions Manual
Use Eye Protection
Use Ear Protection
V ........... Volts
A ........... Amperes
Hz ......... Hertz
W........... Watts
min........ minutes
ADDITIONAL JIGSAWS SAFETY WARNINGS
Warning! Additional safety warnings for jigsaws.
Hold the tool by the insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal parts
of the tool "live" and shock the operator.
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body leaves it unstable
and may lead to loss of control.
........ Alternating Current
........ Direct Current
n
.......... No-Load Speed
0
........ Class II Construction
........ Earthing Terminal
........ Safety Alert Symbol
.../min.... Revolutions or
Reciprocation
per minute
Keep hands away from cutting area. Never reach
underneath the work piece any reason. Do not insert fingers
or thumb into the vicinity of the reciprocating blade and
blade clamp. Do not stabilize the saw by gripping the shoe.
Keep blades sharp. Dull or damaged blades may cause
the saw to swerve or stall under pressure. Always use
the appropriate type of saw blade for the workpiece
material and type of cut.
When cutting pipe or conduit, make sure that they
are free from water, electrical wiring, etc.
Do not touch the workpiece or the blade immediately
after operating the tool. They can become very hot.
Be aware of hidden hazards, before cutting into walls,
floors or ceilings, check for the location of wiring and
pipes.
The blade will continue to move after releasing the
switch. Always switch the tool off and wait for the saw blade
to come to a complete standstill before putting the tool down.
Warning! Contact with, or inhalation of dusts arising from
cutting applications may endanger the health of the operator
and possible bystanders. Wear a dust mask specifically
designed for protection against dust and fumes and ensure
that persons within or entering the work area are also protected.
This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their
safety. Children should be supervised to ensure that they
do not play with the appliance.
The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those
recommended in this instruction manual may present a
risk of personal injury and/or damage to property.
FEATURES
1. Lock-on button
2. Variable speed on/off switch
3. Blade storage compartment cover
4. Shoe plate locking lever
5. Shoe plate
6. Blade support roller
7. Tool-free blade clamp
Additional features (fig. A)
Additional features may be applicable depending upon the
product purchased. The additional features applicable to the
catalogue number purchased are shown in fig. A.
Fitting the saw blade (fig. B)
Hold the saw blade (8) as shown, with the teeth facing
forward.
12

Publicidad

Tabla de contenido
loading

Tabla de contenido