Shark SV70 Manual Del Usario página 4

OPERATING INSTRUCTIONS
Battery Pack Replacement
& Disposal
Your Cordless Vacuum is powered by
Nickel-Cadmium Ni-Cd) batteries, which
must be recycled or disposed of
properly in accordance with state,
federal and local laws.
If uncertain as to how to remove the
battery pack, we suggest you take your
hand vacuum to a reputable small
appliance service technician to have
this service preformed.
Do NOT attempt to replace the batteries
used in this product with any other type
of battery.
The battery pack of your cordless vac is
replaceable, however care should be taken
when doing so. Follow these steps when
replacement is required:
1. Using a #1 Phillips head screw driver,
remove the single screw securing the
battery compartment cover located on
the under side of the unit.
2. To remove the cover, press down on
the battery compartment cover while
sliding towards the rear of the unit.
NEVER open the battery
compartment except to change the
battery.
3. Set aside battery compartment cover
and screw.
4. Using the same Phillips screw driver,
remove the single screw securing the
battery strap. Lift off the battery strap
and set aside with screw.
5. Carefully lift out battery
pack and disconnect
the terminals. (Fig. 8)
6. Connect the terminals
to the new battery pack
taking care to connect
the black lead (-) to the
negative connector first
and the red lead (+) to
the positive connector
second. Place the
new battery into the
battery compartment.
7. Tuck the wiring inside the
battery compartment so that the wiring
does not interfere with the battery
compartment cover when it is
replaced.
8. Re-install the battery strap and
battery compartment cover.
WARNING
: NEVER use ordinary
batteries for replacement, as these may
leak and damage your vacuum cleaner.
Use only battery pack XB14726
provided by EURO-PRO Operating
LLC for replacement.
CAUTION
: NEVER use the unit
without the battery compartment cover
in place.
Note
: Any other servicing should be
performed by an authorized service
representative.
CAUTION
• Use only with the battery pack
supplied with the unit.
• Do not attempt to remove the battery
pack from the unit to charge it.
• Never attempt to throw the battery
pack or unit into a fire or incinerate
it.
• Do not attempt to remove or
damage the battery casing.
• Battery must be recycled or
disposed of properly at the end of it's
service life.
• Do not place batteries on metal
surfaces.
• Do not touch metal parts of the
batteries together as the batteries
will overheat.
Wall Mounting Bracket (Optional)
1. Make sure that the intended wall area
for the wall mounting bracket to be
drilled is free from any hidden
electrical wires, water pipes and gas
lines.
2. Select an appropriate place close to a
wall power outlet (120V., 60 Hz).
Fig. 8
3. Do not mount near direct sunlight,
near a heat source or outdoors.
4. Select an appropriate drill type for the
material to be drilled.
5. Carefully measure and mark the
location of all bracket holes and then
drill holes and screw the wall
mounting bracket onto the wall.
5
OPERATING INSTRUCTIONS
TROUBLESHOOTI NG GUI DE
PROBLEM POSSIBLE REASON
1. Batteries discharged.
Dead battery (battery
2.
HAND VACUUM
won't hold charge).
WILL NOT
No power in electrical
3.
OPERATE
outlet supplying
transformer.
1. The 2 metal pins of the
motorized brush are
MOTORIZED
not in contact with the
BRUSH WILL NOT
vacuum cleaner.
WORK
2. Motorized brush is
clogged up.
Dust cup container is
1.
HAND VACUUM full.
WILL NOT PICK- Dust cup filter needs
2.
UP OR SUCTION cleaning or
POWER IS WEAK replacement.
3. Unit needs recharging.
Dust cup container is
1.
full.
DUST ESCAPING
Dust cup filter is not
2.
FROM HAND
installed correctly.
VACUUM
Puncture/hole in dust
3.
cup filter.
POSSIBLE SOLUTION
1. Charge unit.
Replace batteries. (See
2.
page 5.)
Check fuse or breaker.
3.
Replace fuse/reset
breaker.
Firmly insert the
1.
motorized brush into the
air-intake nozzle. This will
connect the motorized
nozzle to the unit power
supply.
2. Remove all lint, hair etc.
from motorized brush.
Empty dust cup container.
1.
Remove dust cup filter
2.
and check for object(s) in
air duct and remove.
Clean or replace dust cup
filter.
3. Charge unit.
Empty dust cup container.
1.
Review dust cup filter
2.
installation instructions.
Replace dust cup filter.
3.
6