Parts List; Date Of Manufacture - Evenflo Reja de acceso a presión Instrucciones

To prevent serious injury or death, securely install gate and use according to manufacturer's instructions and warnings.
• NEVER use with a child or pet able to climb over, dislodge, or open the gate.
• NEVER leave child unattended.
• To prevent falls, NEVER use at the top of the stairs.
• Intended for use ONLY with children 6 months through 24 months.
• To ensure proper fit, use ONLY in openings between 31 inches (79 cm) and 36.25 inches (92 cm) wide.
• To help prevent entrapment, DO NOT allow space between bottom of gate and floor.
• Use ONLY with locking/latching mechanism securely engaged.
• To help prevent gate from dislod ging, make sure all four end caps fit securely against wall or doorway opening.
• To prevent falls, DO NOT attempt to step over gate.
• STOP using gate if any parts are missing or become damaged to help ensure proper gate function.
• Use in doorways with wooden frames. When installing against drywall, ensure mounting surface is reinforced with a wall stud to help
prevent damage.
• Periodically check all fasteners to be sure they are tight and secure to prevent gate from dislodging.
• Pressure-mounted gates may dislodge if significant pressure is placed against them. Avoid applying significant pressure or weight.
• This gate will NOT necessarily prevent all accidents.
• For indoor use ONLY.
• PET STRANGULATION HAZARD – Pets can force themselves into very small openings. Use this gate only with pets whose head or body
WILL NOT fit into openings in the gate, between the gate and the floor, or between the gate and the wall.
• Ensure gaps between the safety gate and the side of the door frame are approximately equal.
• Ensure child is kept away from the gate when closing or opening it to prevent injury to the child, such as from pinching.
Important Information
IMPORTANT: Failure to follow installation instructions could result in serious injury to your child. Read these instructions
completely and keep for future reference.

Parts List

If you are missing parts, visit us at www.evenflo.com or call ParentLink at 1-800-233-5921.
Top-of-Gate Adjustment
Bumper Housing (3)
Gate (1)
(Product may vary from illustration.)
Registration Information
Please register this product so we can reach you if there is a safety alert or recall. We will not sell, rent, or share your personal infor-
mation. To register your product, please complete and mail the card that came with it or visit our online registration at:
w ww.evenflo.com/registerproduct.
For future reference, record the Model Number and Date of Manufacture below.
Model Number:
•
www.evenflo.com • USA: 1-800-233-5921, 8 AM – 5 PM EST
• Canada: 1-937-773-3971 • México: 01-800-706-12-00
WARNING
Bottom-of-Gate Adjustment
Bumper Housing (3) Adjustment Bumper (4)
Extension (1)

Date of Manufacture:

Measure and record the width of the doorway opening in which you will install the gate. The extension should be used in
doorway openings ranging from 32.9 inches (83.6 cm) to 36.25 inches (92 cm) wide. If the doorway opening is 31 inches (79
cm) to 32.9 inches (83.6 cm ) wide, the extension is not needed.
B
C
A B
C
D
E
B
A
E
B
C
NOTE: Make sure the adjustment bumpers and thei r housings are pushed in all the way.
Assemble Gate
Assemble Gate Without Extension
B
C
1. Insert a top-of-gate adjustment bumper housing
each top corner of the gate frame B , as shown.
2. Insert a bottom-of-gate adjustment bumper housing
into each bottom corner of the gate frame D , as shown.
3. Insert an adjustment bumper into the adjustment
E
bumper housing ( A and C ) at each of the four corners
of the gate frame , as shown.
B
into
A
C