Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
The cycle tune-up must be performed at initial installation of the LIVESTRONG E-Series for optimal per-
formance and longevity. Please read and follow all instructions below. If the LIVESTRONG E-Series is not
installed and tuned as described, components may wear excessively and the LIVESTRONG E-Series may
become damaged. If you have questions about the installation, please contact MATRIX Fitness Systems.
1RWH 6RPH PDLQWHQDQFH SURFHGXUHV UHTXLUH :' UH¿OODEOH VSUD\ ERWWOH UHFRPPHQGHG RU %UXQR[ VSUD\
lubricant, and White Lithium grease.
1.
Make sure that the LIVESTRONG E-Series is level. If the LIVESTRONG E-Series rocks on the
ÀRRU WXUQ WKH OHYHOLQJ IHHW XQGHUQHDWK WKH IURQW DQGRU UHDU VWDELOL]HU XQWLO WKH URFNLQJ PRWLRQ LV
eliminated.
2.
Verify Emergency brake function to assure that emergency brake functions correctly.
3.
Brake pad calibration: Turn resistance knob counterclockwise as far as possible (minimum bra-
NLQJ HIIHFW YHULI\ WKDW WKHUH LV D VOLJKW VHSDUDWLRQ RI WKH EUDNH SDG IURP À\ZKHHO %UDNH SDG
VKRXOG EDUHO\ WRXFK WKH À\ZKHHO ZKHQ UHVLVWDQFH NQRE LV WXUQHG FRXQWHUFORFNZLVH DV IDU DV LW
can go.
4.
Apply WD40 or Brunox spray lubricant to the brake pad using the lubrication holes on the plastic
part or the brake pad and externally on the felt pad. Make sure brake pad is thoroughly soaked
IURP HQG WR HQG ZLWK OXEULFDQW VSUD\ 7KHQ ZLSH WKH H[FHVV RII IURP WKH À\ZKHHO
%HVW 3UDFWLFH 8VH D UH¿OODEOH VSUD\ ERWWOH ¿OOHG ZLWK QRQDHURVRO :' SXUFKDVHG E\ WKH
gallon (3.7 L) at the local hardware store.
5.
Apply Lithium grease to the threads on the lower end of the brake rod. First, turn the Resistance
knob clockwise until it stops. Apply a small amount of white lithium grease to the threads on the
brake rod above the two lock nuts. Then, turn the resistance knob counter-clockwise until it stops.
6.
Apply Lithium grease on the metal threads of all the adjustment knobs.
7.
Verify four (4) Allen nuts on RS pulley for tightness. If loose, apply LocTite Threadlocker Blue-242
and retighten.
8.
Verify R and L crank arm Allen bolts for tightness. If loose, apply LocTite Threadlocker Blue-242
and retighten.
9HULI\ EHOW WHQVLRQ &KHFN LI EHOW GULYH LV ¿UPO\ WLJKWHQHG DQG GRHV QRW VOLS ZKLOH ULGLQJ XQGHU
resistance load. In case that the belt slips, proceed using the adjustment technique as described
on page (28). Please note that a belt drive gear never shows slack. In case of adjustment do
not apply too much tension.
10.
Wipe down bike frame with rag moistened with WD-40
11.
Some parts of the LIVESTRONG E-Series may become loose during shipment. Check crank
arms, check all exposed screws, bolts, and nuts, and make sure that they are properly tightened.
12.
Verify that computer is reset for Miles vs. Kilometers and RPM measurement is working properly.
Please see computer manual on page 8-18 for instructions on installation of computer.
Customer Service
1.
Provide basic maintenance instructions to client and direct them to detailed maintenance instruc-
tions (page 24 )
6LJQRII VKHHW SURYLGHG WR FOLHQW WR FRQ¿UP H[SODQDWLRQ RI PDLQWHQDQFH SURFHGXUHVPDQXDO DQG
YHUL¿FDWLRQ RI FRQGLWLRQ RI ELNHV
Version 1.2 2010 EBLS Copyright by Indoorcycling Group GmbH 2010
INITIAL INSTALL CHECKS
|
www.indoorcycling.com
ENG 19
Publicidad
Tabla de contenido
