Maintenance And Service - Bosch PTK 14 EDT Manual Original

12 | English
Preselecting the Impact Force
Various settings for the required impact force can be
preselected with the thumbwheel (5) for impact force
preselection.
The impact force required depends on the length of the
staples or nails and the strength of the material.
When using two staples (DuoTac function), the setting on
the thumbwheel (5) for the impact force must be set approx-
imately one level higher.
Note: Always test the selected impact force on a spare piece
of material first. The optimal impact force setting can only be
achieved through practice.
The figures in the table below are recommended values.
Setting Range for Thumbwheel
6
6 8
Substrate
Softwood
(pine)
Hardwood
(beech)
Chipboard
Wood core ply-
wood
DuoTac
6
6 8
Substrate
Softwood
(pine)
Hardwood
(beech)
Chipboard
Wood core ply-
wood
Practical Advice
19 mm staples cannot be used with this power tool.
u
Therefore you should not use the power tool to attach
ceiling panels with claws for fastening wooden pro-
files or joints.
Avoid pulling the trigger when the magazine is empty to min-
imise wear on the firing pin.
When work is complete, set the impact force on the thumb-
wheel for impact force preselection (5) to relieve strain on
the tension spring.
1 609 92A 661 | (18.01.2021)
10 12 14 mm
14 mm
1−3 3
3−5 6
2−4 4
2−4 4
12
10 14 mm
2−4
4−6
4−6
4−5
Carefully set the tacker head (1) down on the material. Soft
workpieces (e.g. pine wood) could be damaged if you press
down too hard.
The power tool is designed for short-term use and heats up
in continuous operation. Performance reduces as the tem-
perature increases. The S2 operating mode denotes short-
term operation with a maximum operation time of
10 minutes of constant use.
Switch the power tool off after this time and allow it to cool
down.
Removing Jammed Staples
Pull the plug out of the socket before carrying out any
u
work on the power tool.
– Turn the power tool around.
– Press the magazine release (6) and pull the magazine (9)
out of the back of the tool at the same time.
– Remove the jammed staple. Use a pair of pliers for this, if
required.
– Slide the magazine (9) back in until it clicks into place.
Fill the magazine in good time. A staple strip that is too
u
short may be the cause of jammed staples.

Maintenance and Service

Maintenance and Cleaning
Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Bosch Power Tools