Specific Safety Rules; Extension Cords - Black and Decker BDEQS300 Manual De Instrucciones

Lijadora de hojas de 1/4
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

moving parts. Loose clothes, jewelry or
long hair can be caught in moving parts.
g) If devices are provided for the
connection of dust extraction and
collection facilities, ensure these
are connected and properly used.
Use of dust collection can reduce
dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use
the correct power tool for your
application. The correct power tool
will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the
switch does not turn it on and
off. Any power tool that cannot be
controlled with the switch is dangerous
and must be repaired.
c) Disconnect the plug from the
power source and/or the battery
pack from the power tool before
making any adjustments, changing
accessories, or storing power tools.
Such preventive safety measures
reduce the risk of starting the power
tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or
these instructions to operate the
power tool. Power tools are dangerous
in the hands of untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any
other condition that may affect the
power tool's operation. If damaged,
have the power tool repaired before
use. Many accidents are caused by
poorly maintained power tools.
f) keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to
bind and are easier to control.
g) Use the power tool, accessories
and tool bits, etc. in accordance
with these instructions, taking into
account the working conditions and
the work to be performed. Use of
the power tool for operations different
from those intended could result in a
hazardous situation.
5) SERvICE
a) have your power tool serviced by a
qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power
tool is maintained.

SPECIFIC SAFETY RULES

• hold tool by insulated gripping surfaces
when performing an operation where the
cutting tool may contact hidden wiring
or its own cord. Contact with a "live" wire
will also make exposed metal parts of the
tool "live" and shock the operator.
WARNING:
glasses. Everyday eye glasses are NOT
safety glasses. Also use face or dust
mask if operation is dusty. ALWAYS
WEAR CERTIFIED SAFETY
EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA
Z94.3)
• ANSI S12.6 (S3.19) hearing protection
• NIOSH/OSHA/MSHA respiratory
protection
• Sanding of lead-based paint is not
recommended. See Sanding Lead
Based Paint for additional information
before sanding paint.
• C lean your tool out periodically.

ExTENSION CORDS

When using an extension cord, be sure to
use one heavy enough to carry the current
your product will draw. An undersized
cord will cause a drop in line voltage
resulting in loss of power and overheating.
The following table shows the correct
size to use depending on cord length and
nameplate ampere rating. If in doubt, use
the next heavier gage. The smaller the
gage number, the heavier the cord.
Minimum Gage for Cord Sets
volts
120V
0-25
240V
0-50
AmpereRating
More
Not more
Than
Than
0
-
6
18
6
-
10
18
10 -
12
16
12 -
16
14
SYMBOLS
The label on your tool may include the
following symbols. The symbols and their
definitions are as follows:
V ..................volts
A ..................amperes
Hz ................hertz
W .................watts
min ..............minutes
or AC ......alternating current
or DC ...direct current
n o ................no load speed
................Class I Construction
................earthing terminal
...............safety alert symbol
................Class II Construction
................Read instruction manual before use
.................Use proper eye protection
................Use proper hearing protection
................Use proper respiratory protection
3
ALWAYS use safety
Total Length of Cord in Feet
26-50
51-100
51-100 101-200
American Wire Gage
16
16
16
14
16
14
12
Not Recommended
(grounded)
(double insulated)
101-150
201-300
14
12
12

Publicidad

Tabla de contenido
loading

Tabla de contenido